Jump to content
SAU Community

Recommended Posts

hey chaps.. i kno this has probably been covered before but would appreciate peoples opinions on the matter, i have a fairly standard RB20det with exhaust, pod, boost controller and front mount.... recently i purchased a T3 ball bearing turbo with external gate. I am not a complete moron but would like some advice or somebodies knowledge on how else to equipe the motor for somewhere around 300rwhp

was thinking--- after market manifold fabricated to suit my gate

a walbro fuel pump

GTR or sard injectors

sequential BOV

re-mapped ecu or piggyback?

i need sort of mid range power for drift so to me, this application sounds about right... if anybody has done a similar engine enhancement to this it would be greatly appreciated if they could point me in the right direction of how they went about it and the power outcome.

thanks for your time :wassup:

Link to comment
https://www.sau.com.au/forums/topic/73628-ceff-engine-upgrade-time/
Share on other sites

the parts u listed there should get u close to that figure..

i also had a similar setup..

T3, rb20, GTR fuel pump, Boost COntroller, 2.5 inch turbo back zorst and Larger Cams, on around 13psi got me around the 170rwkw mark..

things missing were injectors, FMI and maybe a remapped ECU (toshi from the forums here can do it for like 200 bux) .. shoud bring it close to the 210 rwkw mark..

GTR - injectors = 250 bux

ECU = 200 bux

FMIC = 700 bux installed including the the GTR sized intercooler.

U might have to wind the the boost to say 15-16 pounds to get that much thou..

Ive seen that setup before..

gnarly cheers for the feed back man

i gotta get a t3 flange welded onto my manifold as the huffer is currently sporting a t4 pattern and modify the external gate situation to suit my normalair-garret waste gate... already got the cooler installed and its making reasonable horse power as is, but a little more couldnt hurt surely!

know anywhere i can get sum GTR injectors for 250 quid?

If you plan to use it for drift, in my opinion, the best thing you could do is sell up all the goodies you have for your RB (including engine) and do an SR20det converion. The conversion is very simple and makes the car SOOOO easy to slide you will be amazed. The extra tourque does not go astray either.

I have driven one SR cefiro, one SR laurel and frequently drifted another SR20 laurel (stock with 0.7bar boost and coilovers and diff) and i must say i was completing sections of Qld Raceway i could only have dreamt of in my RB powed laurel.

Go for the SR.

yer i used to pilot a SR 180.. cant beat the sound and kick of an sr but im quite content listening to my truck like RB at the mo... although an SR would give a lot less under steer wich is better for dori... tell u wat when i lunch my RB il gladly swap it for a black top sr or something---- dont really have the $ for a 26 i can hardly afford a big mac meal these days :headspin:

  • 2 weeks later...

hey all... sorry to re-kindle an old thread but any one that has done a T3 or other conversion how did u go with the oil lines for the turbo, like can use standard? my mate got one made up of a tephlon (spelling?) style pipe with braded coating cost him 100bux

proly should be in the mech section but i only read this thread! :kick:

cheers peeps!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be. Could also be that they sit around broken more. To be fair, you almost never see one driving around. I see more R chassis GTRs than the Renault ones.
    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy required to ignite the fuel are not significant factors when running at 1500-4000 rpm, and medium to light loads, like nearly every car on the road (except twin cab utes which are driven at 6k and 100% load all the time). There is no shortage of ignition energy available in any petrol engine. If there was, we'd all be in deep shit. The calorific value, on a volume basis, is significantly different, between 98 and 91, and that turns up immediately in consumption numbers. You can see the signal easily if you control for the other variables well enough, and/or collect enough stats. As to not seeing any benefit - we had a couple of EF and EL Falcons in the company fleet back in the late 90s and early 2000s. The EEC IV ECU in those things was particularly good at adding in timing as soon as knock headroom improved, which typically came from putting in some 95 or 98. The responsiveness and power improved noticeably, and the fuel consumption dropped considerably, just from going to 95. Less delta from there to 98 - almost not noticeable, compared to the big differences seen between 91 and 95. Way back in the day, when supermarkets first started selling fuel from their own stations, I did thousands of km in FNQ in a small Toyota. I can't remember if it was a Starlet or an early Yaris. Anyway - the supermarket servos were bringing in cheap fuel from Indonesia, and the other servos were still using locally refined gear. The fuel consumption was typically at least 5%, often as much as 8% worse on the Indo shit, presumably because they had a lot more oxygenated component in the brew, and were probably barely meeting the octane spec. Around the same time or maybe a bit later (like 25 years ago), I could tell the difference between Shell 98 and BP 98, and typically preferred to only use Shell then because the Skyline ran so much better on it. Years later I found the realtionship between them had swapped, as a consequence of yet more refinery closures. So I've only used BP 98 since. Although, I must say that I could not fault the odd tank of United 98 that I've run. It's probably the same stuff. It is also very important to remember that these findings are often dependent on region. With most of the refineries in Oz now dead, there's less variability in local stuff, and he majority of our fuels are not even refined here any more anyway. It probably depends more on which SE Asian refinery is currently cheapest to operate.
    • You don't have an R34 service manual for the body do you? Have found plenty for the engine and drivetrain but nothing else
    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
×
×
  • Create New...