Jump to content
SAU Community

Recommended Posts

hi all,

i have an auto '89 r32 gtst, just recently off the boat.

i'm finding that when i give it some stick, the revs drop off, then surge again, then drop off, then surge etc etc. eventually the car conks out and i have to restart.

if i'm just driving normally, it appears ok...any ideas what this could be?

any help at all would be great...

sig.

Link to comment
https://www.sau.com.au/forums/topic/75903-revs-drop-off-help/
Share on other sites

haha sounds exactly like what i had...very very annoying, mine was intermittent too then got worse and worse. turns out it was the AFM (airflow metre). you can find it just after the airbox/pod on the intake pipe. i just got contact cleaner and sprayed the crap out of the element and plugs.

however from what ive read, some of the AFM's are brittle on the inside where the circuit board has to bridge out to the plug and causes problems. if the contact cleaner dont work then either get a new AFM or cut open the existing AFM clean up the contacts on the board and reseal the metre with silicon.

good luck mate. i feel your pain. could be something else too, but AFM is what i would look at first, cause it only takes 20-30 mins

hey thanks heaps flagger - yeah it's ticking me off big time. i'll grab some contact cleaner and give it a go - i guess you remove the airbox, do you then remove the actual afm or just spray down into the guts of it through the metal filter? guessing i have to remove the whole device...

  • 2 weeks later...

hey when your car surges and then eventually turns off.. do u get alot of smoke blowing out of exhaust?. and surges to pretty much 0rpm then back to liek 1000rpm and back and forth?.. i cleaned my afm 2 days ago fixed the problem but its back :( but it doesnt happen all the time?...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...