Jump to content
SAU Community

Recommended Posts

I've recently noticed more and more blue smoke coming from my exhaust. It smells horrible, burns my nose and makes my eyes water if I get a good enough wiff of the shit.

I know this bad news but can I:

a) Determine whether it's the turbo, the rings, or something else easily?

B) Drive it around safely? Will it get worse?

Any other comments appreciated...

Mods are as follows:

RB20DET w/ custom plenium, Microtech LTX8, bov, stock rb20 turbo (Hoping this is shot and not the rings.. excuse for a bigger one :rofl:) fmic etc etc.. Internals and all the rest are stock

Car is going in for a service at Proconcept at West Ryde on Monday morning..

Link to comment
https://www.sau.com.au/forums/topic/79788-blue-smoke-rb20det/
Share on other sites

Smoking all the time, only on boost, only when coming off boost?

Spend half a day pulling the turbo off, take it somewhere to get all the seals etc checked out. If it is stuffed, replace it, if it isnt chuck it back on and it shouldnt have cost you too much money.

Smoking, well, all the time unfortunately.. So guessing it could be the rings, smoking alot more on boost though (naturally)

It's smoking enough to notice the smoke when your stopped at traffic lights, if you look out one of the windows

EDIT: Just went for another drive, it's funny, sometimes it blows smoke at idle whereas other times it doesn't (well if it does then you cant even notice it)

I would go back to the guy you bought it off if he didn't tell you about it cause it sounds like you might have to open the engine up to fix this one i would say it is the rings my mate had the same problem blue smoke is a bad bad thing, i take it you didn't get a warrenty with the car

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...