Jump to content
SAU Community

Recommended Posts

i was there lat night too, i saw u there RSTME but i didn't come over i didn't know it was your car, next time i will. what happened on the run where your car got tail happy about half track, nice save from the wall anyway. it was a packed night for cars anyway some nice 32's and i'm always a big fan of the rotor's. i go usually every week anyway so hope to see some of you there sometime.

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464388
Share on other sites

I spectated with a mate. Heaps of Holdens and Fords, too many actually ;)

Afew rotors out which is good to see (most likely testing for this sundays bracket meeting). They had a few oil downs in the staging area of 1 of the lanes so that's why the nites racing was slower than normal (along with a massive entry of cars).

The burnout comp was quite good considering the quality of cars.

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464584
Share on other sites

the holdens and fords sucked LOL he he he he they were all so slow....they wish they had a chance against the classy cars ;) like skylines he he he he my friend told me skylines r taxiz in japan :S is that true??

90% of Taxis in Japan are Toyota crowns .

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464670
Share on other sites

plenty of Lines at WSID last night,i spoke to 2 guys,neither came on here,was a r34 GTR with coverd up #plates 'o0OhH!'  

did anyone see ME:) ???  

i had 3 runs  

15.2

20.8  LoL

15.1

full zorst,pod,13psi,Automatic & crap tyres.

I was there with the covered number plates in the 34 GTR M-spec .

Very busy , i had 4 runs all in the 12's with a best time 12.3 @ 113 mph but my stock clutch couldnt hold , my best 60ft was 2.05 .

A silver 33 GTR series I was doing 12.5-12.6 .

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464679
Share on other sites

I noticed you werent launching very hard. Thought you may have been taking it easy for your first time in the new 34 ;)

I launched at 5500 the first time but the clutch wouldnt hold then i backed off , one time i launched at 2500 but the last run was the best 4500 .

GTRS need to be launched at 5500 -6500 to get a good 60 ft

Link to comment
https://www.sau.com.au/forums/topic/80520-wsid-last-night/#findComment-1464719
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...