Jump to content
SAU Community

Recommended Posts

Item:

standad rb26 cams: $200 for both

standard rb26 rods: $200 for all of them

standard rb26 crank: $400

standard rb26coil packs: SOLD!!

Location:brisbane - PICKUP ONLY

Item Condition: all good, and inspected

Reason for Selling:upgraded

Contact Details:

PM

Edited by druzilla32
Link to comment
https://www.sau.com.au/forums/topic/87322-gtr-stuff-brisbane/
Share on other sites

hey there - when you say items all good and inspected, who has done this inspection ( mainly the crank and rods that I'm asking about).

cheers.

the guys building my motor.

they are currently being cleaned and i should have them bagged by this arvo.

i have been offered $500.. but the buyer is interstate.

if nobody else is interested, they will be sold interstate

where abouts are you ( suburb?). I can possibly get someone to get over there if easier than you sending interstate. If the goods are all OK I'll give you $500 cash on the spot ( just need to confirm how close by you are).

cheers.

Hi John here ,

I'd be interested to find out if you still had the PlugPacs ?

John 0409 498 495 .

Cheers

( i,m in Brisbane )

(Use this as a guide for new threads. Delete and/or copy the fields as needed - dont forget to add your location in the description field above. Delete this message)

Item:

standad rb26 cams: $200 for both

standard rb26 rods: $200 for all of them

standard rb26 crank: $400

standard rb26coil packs: all 6 for $120 (my car was missing, then i cleaned all the packs and connections and i didnt have a problem since)

Location:brisbane - PICKUP ONLY

Item Condition: all good, and inspected

Reason for Selling:upgraded

Contact Details:

PM

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...