Jump to content
SAU Community

Recommended Posts

Ok so i got a highmount TD-06 set up on my R32 and was jsut wondering if anyone else had the same turbo, what mods do they have and what is the turbo good for at the end of the day.

With the right mods to the Rb20 what do you recon the over all figure i could get out of it without spending thousands on a complete rebuild and what rpm are you making boost???

Cheers B

Link to comment
https://www.sau.com.au/forums/topic/88536-td-06/
Share on other sites

i have one, but ive got a blown motor, so havent dynoed it, best person to talk to is ROY, they are a great turbo for the rb20 and can make aroung 250rwkw with supporting mods. im hoping to get as close to 300rwkw with mine, but i have a worked engine. I may end up geting T67 to replace my TD06.

Link to comment
https://www.sau.com.au/forums/topic/88536-td-06/#findComment-1598545
Share on other sites

have currently bolted one to a rb20 with an 8cm rear housing....in terms of mods, nothing major just front mount pod exhaust made 230rwkw and actually ran 12.2 last night at WSID (congrats tim)..... my old setup was rb25 with cams etc etc made 265rwkw with a 12cm rear housing......in all truth to see a 20g reach 300rwkw is a big task....however the 25g/t67 will see you well over 300rwkw, however on a rb20 you'll lose alot down low.

What really freaked me out was when we put a 700hp garrett gt turbo on a rb20 with a stock motor with frount mount and exhaust and boost, it made 266rwkw!!

Link to comment
https://www.sau.com.au/forums/topic/88536-td-06/#findComment-1598721
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...