Jump to content
SAU Community

Recommended Posts

I just bought an r32 gts-4 and I had no dramas when I picked it up but Ive noticed a few problems start up.

On start up it runs very ruff and sometimes stalls, if I give a bit of juice after a second or two it seems to sort it self out.

Also after ive given it a bit while driving it back fires when you back off and the next few times you touch the pedal it also back fires.

The car only has a filter and 3in cat back exhast!

So far ive done the plugs, fuel filter, reset ecu, cleaned air flow meter and tryed injector cleaner. It runs smoother but still plays up. Im going to try insulating the coils to see if it makes any difference.

I did notice there is some damage to the centre muffler so that maybe causing the back firing.

GTS-4some, First up, I would pull apart the IAC valve located near the throttle body and give it a clean. This controls your idle speed. If the IAC valve is fine I would then go onto the sensor that controls this. Not directly but the ECU input would be the 2 pinned coolant temperature sensor. Located in the water jacket normally 9 times out of 10 up the front of the engine.

As for Tommo's problem, I would say that if the coolant temp sensor is not telling the computer that the car is now hot, you will still have rich mixtures and this will kill an exhaust in no time. You will find that you will get poor fuel consumption and be down on power.

Cheers

Sumo

P.S. Im telling you what I know in my universal applications of how cars work, I have had bugger all expirience with skylines in particular, but once you get your foundations straight you can normall apply this to most cars.

How damaged is your exhaust ? A badly damaged exhaust will cause all sorts of problems.

I would also suggest checking the ignition timing and possibly the crank angle sensor since RB20's sometimes get problems in that area.

On start up it runs very ruff and sometimes stalls, if I give a bit of juice after a second or two it seems to sort it self out.

I had this problem.

Injectors are clagged.

You will also find if you try and give it a quick stab of the throttle it will stumble and not rev up as it should.

If you drive it immediately after you start it you will feel a nasty flat spot on the accelerator.

Once the injectors and fuel warm a little the fuel atomizes better, which is why once its warm it feels ok.

I still found mine had a real slight flat spot on the tip of the accelerator, i.e limping around a car park with really really light throttle it could be felt.

Edited by Cubes

Throttle body and valve were clogged up so I cleaned them out but was still having problems.

I got a mate at nissan to put it on a diaignostic computer everything showed up fine, air fuel and everything, and no error codes but didnt feel right!! There is no exhast leaks, I checked it, so the damage cant be to bad!

I got it dynoed and it only dynoed at 108kw at all four and was running lean!!

I got the fuel pump flow tested and its screwed so im replacing it tomorrow with a walbro then getting another run done.

The pump was only running around 1.0 to 1.5 litres per min.

I will post after the pumps in, thats the major problem, but the injeactors i think will need a cleaning too!!

Thanks for the input everyone!!!!

I now have a couple of other things to check out if im still having problems tomorrow!!

While its there give it a carbon clean.

I think thats what its called.

A mate of mine during school was a mechanic, I often saw him attaching a can of something via a hose in front of the t/b, while the motor was running he would squirt the can, the car would run like crap but it apparently removed all the sludge and junk in the plenum/tb/valves.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...