Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Nah, 13 is not too bad, at higher revs you want it to lean off a bit, that is were you can make some real power gains, too lean and bang. 12.0-12.8 is usually about right, and quite safe. Too lean is bad for all engines, not just R32 GTS.

See'ya:burnout:

old trick i have never done it...but heard about it...couldnt be took good but when travelling along kill the ignition and keep foot to floor then start car again. maybe it is just for carbie motors..but meant to send to 20foot flame and loud bang out the back. :-D

alternatively the new apexi PFC has misfire system, (anti-lagg) so u can set it up to burn excess fuel in the turbos and it apparently shoots flames out the exhaust..even with a cat?

mine pops and crackles like a bowl of rice bubbles. I love it, only had flames twice(i still run cats) from my exhaust. What we've done though is richen up my top end and a bit under trailing throttle to preserve engine on speed runs(depending on tempt its a safe guard of it leaning out to much).

The pops can be heard on my launching videos on my website when i lift off gives a bit pop pop crackle pop. :)

Got car booked in today to get a leak fixed(at the flange after extractors/before cats) and a balance pipe put in(deeper note hopefully) but also to get a cat replacement pipe made up for track days. No-one has wanted to make me up a set of screamer pipes yet ;)

I'd love a set, straight off the extractors exiting out the sides.. My old auto ute used to run hi flow cats(proper 1's with enlarged entries/exits etc and not a gutted cat) and it was loud as hell.. popped and crackled a bit(hadnt fiddled with ecu at time) but also droned alot less in cabin due to the cat not causing restriction.

Personally if you want to run without a cat, get a replacement pipe made up for track/drag work and "accidently" leave it on at times.. but dont be suprised when you get reamed if caught.. Alternative would be get some cats, gut them and fit them yourself.. no exhaust shop wants to touch the cats as if they do, they cop a $25,000 fine or there abouts(i've asked em :P). Overall though be careful, while its legal in some countries(nz, various states in USA) its highly illegal in australia.

A mate of mine has an R33 GTS-T with no cat and a big fuel reg. It drags flame about 2-3 feet for a few seconds after backing off at high rpm. We were standing in the Nasho at the 35 corner watching each other do fly bys. Locals at Stanwell wen't too happy!

Originally posted by Hicks

Have the external waste gate pointing to the road I say. Shoot the flames onto the bitumen.

My setup is just like this, but the flames came out the exhaust after letting off the throttle. Never from the wastgate (that I was told). Nice blue flames too, (that I was told) and a couple nices pops. No cat by the way.

Put cat in, stopped the flames.

An old very nice looking chev gets around these parts and must have the switch to do the flames. He quite often drives past us and lets them go. We first saw it on the highway, he heard us talking on the UHF and then put on a show.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...