Jump to content
SAU Community

Recommended Posts

The following are off a R33 gtst rb25det.

- standard intercooler (good nic) $70

- standard computer (works fine) $250

- factory air flow meter (works fine) $150

- factory injectors $200

- factory fuel rail $100

- turbo heat shield $30

- manifold heat shield $30

- factory coil packs $150

- factory plenum $200

- standard dump pipe $50

- oil cooler aftermarket $70

- pedal + surrounds/bracket $50

- steering wheel (series1) $70

- headlight bulbs (H1) $30

- 2x HKS braided lines from turbo kit $30

- factory orange side indicators $20

- carbon fibre bonnet with pins (this has flung off as i left the pins open and hit my roof, so i took it off) the ends are cracked but can be easily repaired. $400

prefer pick-up. i live in sydney eastern suburbs. prices are negotiable.

Link to comment
https://www.sau.com.au/forums/topic/93361-r33-bits-n-pieces/
Share on other sites

what are the braided lines ( water, oil?) and will the braided lines fit an rb20det?

IF SO VERY INTERESTED!

Edited by 66 skyline gt

hello there

I am after 2 things:

1. the rear boot cover- it's the grey backing cover which covers up the battery and speakers in the boot

2. the rear speaker brackets(the 'platform' thing where the rear speakers are mounted on)

thanks

VIC

The following are off a R33 gtst rb25det.

- standard intercooler (good nic) $70

- standard computer (works fine) $250

- factory air flow meter (works fine) $150

- factory injectors $200

- factory fuel rail $100

- turbo heat shield $30

- manifold heat shield $30

- factory coil packs $150

- factory plenum $200

- standard dump pipe $50

- oil cooler aftermarket $70

- pedal + surrounds/bracket $50

- steering wheel (series1) $70

- headlight bulbs (H1) $30

- 2x HKS braided lines from turbo kit $30

- factory orange side indicators $20

- carbon fibre bonnet with pins (this has flung off as i left the pins open and hit my roof, so i took it off) the ends are cracked but can be easily repaired. $400

prefer pick-up. i live in sydney eastern suburbs. prices are negotiable.

hello there

I have a r33 series 2 GTS-T.

do you sell the

1. front lip

2. rear speaker bracket

3. the cover that covers up the battery compartment in the boot

please let me know. :P thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...