Jump to content
SAU Community

Recommended Posts

Hi every1,

I know this is SKYLINER forum,

Just need car lovers help me out. thanks!

my car got stolen at LiverpoOL area, on tuesday night,

Its a black Nissan 300ZX, 18' Rim, Round lights (ferrari lights)

Number plate AMK24S.

his a pic

mypic7.jpg

Please keep a look out and if spot please report to the police!

Thank you & help stop car theives low life bastard!!!!

darrien.

0421592836

Edited by ZXFIRE
Link to comment
https://www.sau.com.au/forums/topic/93491-black-300zx-stolen-liverpool-area/
Share on other sites

I saw a pretty suss looking 300zx on the way to work today.. just where it was parked and the way it was parked, looked like it was just dumped there. I will drive by it again on the way home and check it out for you.

went and checked it out, wasnt it sorry :P

different wheels and paint was more faded.

Goodluck with getting it back

SLIM?

where did u see it?

I am desperate to search for it! maybe they change the wheel?

can i get the location where u saw it?

thanks, SLIM!

this was in West ryde, im certain it wasnt yours, the paint looked really old, and I forgot to check, but I think it had different tail lights, ill check again today if it is still there and tell you the st name

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...