Jump to content
SAU Community

Fs My04 Wrx Evolution 7 Model- Full Sti Bodykit

dori180
 Share

Recommended Posts

dori180 Enthusiast

dori180

Posted
Posted

Hey all

Selling the wrx- got the drift bug so its time to go

Immaculate throughout very well looked after and only 1 owner in the year since it was built

It is the evolution 7 model which means it has a full leather interior front and back and also a sunroof (summer is just round the corner)

Is WR blue mica in colour and has 17'' gold dished rims to contrast it

Also has GFB stealth blow off valve and a typhoon cat back exhaust system for that boxer rumble

Has been fitted with a full STI bodykit including big mofo bonnet vent-looks pretty tough and goes very well for a rex- only ever run on bp ultimate and taken to subaru for service every 5000k's

anyway pictures are worth 1000 words so look on

Front on

Rear shot

Rims

Angle on

Money shot

Interior

Zaust

Chasing $33,000 Negotiable

Contact me for all serious queries please

0404 136 711

Cheers

Dan

dori180 Enthusiast

dori180

Posted
  • Author
Posted

its actually fully tiptronic and shifts hellavalot fast if that softens the blow- ive had a couple people considering buying it and doing a manual conversion but just offering lowball offers :unsure:

thx for the free bump- feel free to call for any further info all

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...