Jump to content
SAU Community

Recommended Posts

Hi Skliner's,

wsup inda mofo.............anyways,

Any practical experience with this particular kookey looking type of tyre.???

I'm looking to purchase (@$230.00 each) these to go on my Enkei's, now!!!

I've absolutely had a gut full with my noisy Dunlop SP3000A's!!! :P

Many thanx in advance!

Superspit Mark.

Link to comment
https://www.sau.com.au/forums/topic/94996-goodyear-eagle-f1-tyres-wotdurekon/
Share on other sites

I have Dunlop 3000A 235x45x17s at the moment. They seem reasonable. I havent hadnt with noise, but that hasnt reall been a concern for me.

Before that had Goodyear Eagle F1's, which were 215x40x17 from memory. They were pretty awful in the wet, but seemed quite decent otherwise, however they wore quickly. Id tend to agree with Cubes, although I didnt have a lot of profile and they didnt have a lot of tread and were fairly slick as it was, so that could have had a lot to do with the tramlining.

Before that had Michelin Pilot Sports. They were the best I've had so far. Wore well, were good in the wet, decent in dry, and quiet.

thanx so far guys. Although the term 'tramline' has me a little bemused!!

I bought the F1's last nite, just for the rear, will do the fronts with same in 2 weeks, (unless the tyre proves to be awful!!).

Noise has cut down drasticly, at most speeds......but they're just not gripping yet!!

Few more blockies should sort them out, I hope?

Thanx!

The F1's I ran were good in the wet as far as wet goes but dry was hrmm ok.

I honestly found the el cheapo simex to grip better in the dry. Every other area of performance the simex fail. :P

Tramline is when the tyre grabs the 'ruts' in the road and pulls the car to one side or another. I felt it more so under braking.

Edited by Cubes

Hmm. Really?

I thought the tread pattern was kind of unusual, in that the grooves werent particuarly deep, so at about 40% and less tread they were quite awful in the wet.

http://verle.be/2.pics/m&d/s2/gyr_hr_gsd3_jpg.jpg

Edited by MarkE
Hmm.  Really?

I thought the tread pattern was kind of unusual, in that the grooves werent particuarly deep, so at about 40% and less tread they were quite awful in the wet.

http://verle.be/2.pics/m&d/s2/gyr_hr_gsd3_jpg.jpg

Man!, One thing for sure...............they are bloody deep grooves.!!

I'm amazed that they could be so quite!!!

Your pic is infact the tyres I've got, but they look like they're already worn out, compared to mine!~!~!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...