Jump to content
SAU Community

Recommended Posts

Item: TD06 - 19C Turbo

Location: Sutherland

Item Condition: Excellent, no shaft play

Reason for Selling: No need for this

Price and Payment Conditions: $1500 ono

Extra Info: see below

Contact Details: Brendan 0423 324 913 [email protected]

Trust/Greedy TD06-19C

This turbo is smaller then a 20G, but will produce around 250rkw on a rb25det.

Pics are below of the turbo as this is currently sitting in my garage.

Turbo can be bolted straight up to a rb25 with no extra work.

There is no shaft play on the turbo what so ever.

post-10680-1132727033.jpg

post-10680-1132727129.jpg

post-10680-1132727183.jpg

post-10680-1132741142.jpg

Edited by z3n2k
Link to comment
https://www.sau.com.au/forums/topic/96010-td06-19c-1500-ono/
Share on other sites

I will provide a dump pipe if you need one, as i still have this.

Looks to be standard dump pipe.

Oil lines would still use the standard ones, but i will throw these in also if you like.

It is a low mount turbo, and it running fine with the standard piping for this, I had the engine taken out by Powerplay and i should have received all parts back, so was running with all standard equipment.

Other mods that were on the car when running that 250kw power run, i am unsure as this was over in Japan and not in AUS, this is just wot came with the car when i received it.

I have this sitting here next to me, and can pick up the oil lines and dump pipe this weekend

Been looking at this for a mate who's after a turbo upgrade.

You have this advertised elsewhere showing the exhaust side pics. Only 4 bolts and not an internal wategate...Is that correct?

So would need an aftermarket manifold/dump pipe/and external wastegate?

If that's the case, how much of the setup have you got to go with it?

Can you post up some more pics showing the exhaust side?

Thanks.....Birnie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...