Jump to content
SAU Community

Recommended Posts

Hi all..

Went to justjap and bought some random things one of them being the volt stabilizer...

Just wondering how and where do people install this?

Running a long earth wire from the battery to the distributor? or?

Any pictures and/or advice would be greatfull.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/96540-raizin-volt-stablizer/
Share on other sites

  • 9 months later...
Hi all..

Went to justjap and bought some random things one of them being the volt stabilizer...

Just wondering how and where do people install this?

Running a long earth wire from the battery to the distributor? or?

Any pictures and/or advice would be greatfull.

Cheers

'err isn't the thing to be installed next to the batt on the boot of a skyline?

I ran 4gauge power cable from my neg terminal in the boot to the bonnet then wired up all earths from there. The stabiliser box is mounted next to my batt in the boot. will get some pics when i get a chance:)

thanks, man. it would clear lotsa things up..

to run the 4 gaugecable to the engine bonnet, u would have to take off ur rear seats and run the wire all the way to the front,yea?

I ran 4gauge power cable from my neg terminal in the boot to the bonnet then wired up all earths from there. The stabiliser box is mounted next to my batt in the boot. will get some pics when i get a chance:)

I had to remove rear seats to run 4 gauge cable. I ran it under the floor carpet on the drivers side with the stock wiring as there are guides in place. The 4G cable is thick and difficult to thread under the carpet without removing bolts for the drivers seat and seat belt anchor.

I then ran it uder the drivers kick panel and through the fire wall just above the throttle pedal which leads to the drivers side wheel arch under the guard. There are guides there that run behind the drivers side headlight in to the engine bay.

Took a total of 6m of cable to run it through properly.

From the 4G cable in the engine bay I mounted all the earthing points.

Afterwards I did notice better sound quality of my audio and brighter interior lights i think... :laugh:

Cheers

Cheers

If anyone could come up with a TUTORIAL on how to do this (with pics too) , it would be good :O

thanks'

I had to remove rear seats to run 4 gauge cable. I ran it under the floor carpet on the drivers side with the stock wiring as there are guides in place. The 4G cable is thick and difficult to thread under the carpet without removing bolts for the drivers seat and seat belt anchor.

I then ran it uder the drivers kick panel and through the fire wall just above the throttle pedal which leads to the drivers side wheel arch under the guard. There are guides there that run behind the drivers side headlight in to the engine bay.

Took a total of 6m of cable to run it through properly.

From the 4G cable in the engine bay I mounted all the earthing points.

Afterwards I did notice better sound quality of my audio and brighter interior lights i think... :laugh:

Cheers

Cheers

isnt there like 4 or 6 wires off the stabiliser? each of these to hook up to individual parts of the engine bay,

CAS, starter, earth strap to block, throttle body etc ??

i would run 1 wire from boot to engine bay, hook stabiliser to the wire in the engine bay then each bit to the spot on the engine...

but thats just me

hmmmm... how do you run the wire from the boot to the engine bay?

i know how to bring it from the boot to the front seat(by taking the rear bak seat off but after that i'm as long as the guy is too.

isnt there like 4 or 6 wires off the stabiliser? each of these to hook up to individual parts of the engine bay,

CAS, starter, earth strap to block, throttle body etc ??

i would run 1 wire from boot to engine bay, hook stabiliser to the wire in the engine bay then each bit to the spot on the engine...

but thats just me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...