Jump to content
SAU Community

Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I have the Stagea floor mats too (but not the centre rear nor the wagon floor mat), and could compare them to R33 Skyline ones, but unfortunately the R33 in question is 150kms away.

Probably best to email the ebay seller and see if they know if they'll fit.

Link to comment
https://www.sau.com.au/forums/topic/96719-floor-mats/#findComment-1755684
Share on other sites

I actually called them, and he's never heard of the stagea, he just buys them from the manufacturer in South Australia.

I gave him a brief description and he thought that the front mats would probly be a close match, but the rears might be the problem, as u know 2 doors dont have much leg room in the rear.

Heres the link: http://cgi.ebay.com.au/NISSAN-CUSTOM-MADE-...1QQcmdZViewItem

Link to comment
https://www.sau.com.au/forums/topic/96719-floor-mats/#findComment-1755698
Share on other sites

The rear of the stagea has as much leg room as an R33, it's the same chassis. also comparing my R33 to my Stagea the rear mats are identical. the only reason the front's might not fit is due to the floorpan being a slightly different shape. if i were to get new mats, i'd get R33 ones.

Link to comment
https://www.sau.com.au/forums/topic/96719-floor-mats/#findComment-1755820
Share on other sites

I think the main difference will be the mats are only for GTR's which are manual as you all know, and i've noticed from looking at genuine stagea mats on slidewize, is that auto's have a cutout on the drivers mat to accomodate the footrest.

Might see if they can add this cutout, also they embroid logos aswell, might see if they can do a custom stagea logo or somthin :D

Link to comment
https://www.sau.com.au/forums/topic/96719-floor-mats/#findComment-1758735
Share on other sites

The guy I talked to said if i can give the manufacturer a pattern of the mats i want, they can custom make them, i'm 99.9% sure that the GTR mats they offer will fit perfectly if the drivers mat has the cutout for the footrest.

I'm a bit of a perfectionist so i want them to fit neatly :P

Link to comment
https://www.sau.com.au/forums/topic/96719-floor-mats/#findComment-1773943
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...