Jump to content
SAU Community

Recommended Posts

Originally posted by INASNT

ok so if i join the 2 lines off the cam covers with a T piece into 1 of the inlets and then from the other port on the can to the intake it will work properly!

Depends, is the interior of your can hollow or filled with filtering material (stainless mesh etc). If its hollow, hooking it up like you said would be as good as not having one.... oil vapours in -> oil vapours out.

Originally posted by Strich9ine

Could i - In theory, Block the hose that goes to the intake altogether?

Yep, I've done so with a suitably sized brass bolt from pirtek. Only thing left to do is hang a filter off the free cam cover pipe or connect it to a vented container. The cam covers can't be blocked off altogether, it needs to be able to release any pressure build up.

The engine doesn't need any oil in the intake, we're not driving rotaries here. :( Macka, adam32 (i think), deesh and myself have diy jobbies. Ask us at the next cruise.

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

but remember theres 2 types of catchcans, some just catch the oil and then u have to empty it,these are basically empty containers which are easy to make, these have to have some sort of breather, the little filters are really good for this as when u just have holes in the top it can sometimes splash out, then theres the catchcans that filter the oil inside it,which kinda have sections in it, inasnt if i was u id drill a hole in the top get a fitting maybe 1/4" and screw it in,then put the filter on top of that,would only cost ya 3 bucks for the fitting and 10bucks for the little filter, there actually little pod filters there cool

Turbomad - my intlet track is the same - zero oil in it, so it'd be pointless for me to install one too.

Yet 2 friends with turbo cars both hae oily inlet tracks....

Strange... Does the oil come from the turbo leaking oil around the bearings or does it come from the crank case brething up into the cam covers and then out that way??

J

Well I guess it can come from both, seeing as our Skylines are still farely new low km cars it's unlikely that boost will slip past the rings pressurising the sump and forcing oil out the rocker, this is mainly a problem with cars running very high boost.

inasnt

i made mine myself and mine is exactly the same as yours except it has a filter/breather on top and a drain plug at the bottom to empty it when the level gets too high.

this type of design is so much simpler than a plumb back design to the sump or filtered air back to the intake and so much easier to make and install.

and the benefits are exactly the same: no oil in the intake, reducing the chance for detonation.

Originally posted by walkoau

inasnt

i made mine myself and mine is exactly the same as yours except it has a filter/breather on top and a drain plug at the bottom to empty it when the level gets too high.

this type of design is so much simpler than a plumb back design to the sump or filtered air back to the intake and so much easier to make and install.

and the benefits are exactly the same: no oil in the intake, reducing the chance for detonation.

so u r running both the cam cover ventilations to the catch can?

there r about 3 ways to set it up, not sure which one i am gonna do.

Have u found much oil in the catch can they way u have yours setup?

Venting to atmo is the easiest way to set up yes, but it's not legal, I got a canary on my vl turbo for that setup.

INASNT the hose was fairly cheap can't remember how much, it's funny I pulled the BOV off the other day and there was some oil around there but not in the catch can, maybe it was always there from before I fitted the can, don't know.

Originally posted by turbomad

Venting to atmo is the easiest way to set up yes, but it's not legal, I got a canary on my vl turbo for that setup.  

INASNT the hose was fairly cheap can't remember how much, it's funny I pulled the BOV off the other day and there was some oil around there but not in the catch can, maybe it was always there from before I fitted the can, don't know.

well i got canaried on friday night! :D

he asked what the catch can was even tho i didnt have it connected and said i couldnt have it there, even tho he didnt now wtf it was.

Originally posted by turbomad

That's a beauty canary's for an empty container not connected to anything haha! How did you go with the roadworthy? Did they pick on your pod too?

he didnt actually write down the catch can on the canary form!

I went today to get it checked by roadworthy place and guess what, i dont have to change any of the crap the cop wrote down! :lol:

COPS DONT KNOW SHIT WAS THE GENERAL THOUGHTS OF THE GUYS THAT WORKED THERE!!

INASNT - wouldn't it be tempting to take the paperwork to that cop and show him that you didn't need to change anything to pass, just to prove to him he has no idea :lol:

But then I suppose he would pick on you evertime he see's you :D

Originally posted by Jay95R33

INASNT - wouldn't it be tempting to take the paperwork to that cop and show him that you didn't need to change anything to pass, just to prove to him he has no idea :lol:

But then I suppose he would pick on you evertime he see's you :D

i was thinking more along the lines of taking my roadworthy certificate and pasting it to his forehead with a 12 gauge shot gun!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...