Jump to content
SAU Community

Im A Sedan Owner Once Again!

inark

By inark,
in Four Door Family & Wagoneers

 Share

Recommended Posts

inark Grand Master

inark

Posted
Posted

http://www.skylinesaustralia.com/forums/in...788372&st=280 - pics here

Its finally here... battery is dead so will need a new one... i accidentally ripped off the bloody petrol latch thing haha so will need to fix that... my gear knob was stolen as was the funky cup holder strap on thing... they f*ked the "Final Konnexion" front bar too... but i will sort that out.

The Bride bucket seat is so friggin tight its not funny... tighter then the ceffies east bear one. Is a bit worn on the side where u get in it... will sew a leather patch on it or something for now. The recliner bucket passenger seat is faded as all hell so will be replaced soon with a Bride Brix copy the same colour as the drives seat.

Brake pads need replacing... thats simple... will replace all the fluids while im at it even tho they look like they have been replaced recently cause the brake fluid and coolant is still clean as.

Cant wait to get it on the road.

Link to comment
https://www.sau.com.au/forums/topic/98436-im-a-sedan-owner-once-again/
Share on other sites
inark Grand Master

inark

Posted
  • Author
Posted

thanks saggy tits :)

ive replaced the GREX knob they stole with another one already and going to get a temp reg tomorrow... have a new battery ready to go in too... time to take it for a spin tomorrow :)

CEF11E - hell yeah... all my bitches... which would be one... who if she knew i said she was me bitch would probably nacker me... lol

gaffa Community Regular

gaffa

Posted
Posted
they f*ked the "Final Konnexion" front bar too... but i will sort that out.

http://www.finalkonnexion.co.jp/english/li...eup_nissan.html

and listed on the Final konnexion website

Final konnexion Authorized Agency

　TeamJetspeed

18 Moss St. Slacks CreekQ4127, Australia.

PH:+61 (07) 3290 2966

FAX: +61 (07) 32902077

Email: [email protected]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...