Jump to content
SAU Community

Recommended Posts

hey ..well today ive "installed" a GFB manual boost controller and a boost guage ..

prob is weather the boost is turned all the way down or up shows no difference on the guage.

the max it shows on the guage is 0.4bar (5.6psi if my maths is right) pretty shitty!!

Boost control install..

1)i unplugged the 2 pipes from the standard solenoid

2)removed the T piece

3)replaced the pipe from the intercooler with the pipe that comes with the boost

controller (in case of standard restictor in the pipe)

4)basically put the boost controller in place of the T piece with the arrow facing towards the turbo

5)put a large screw in the end of the other pipe that originally went to the standard boost solenoid.

is this right?

Boost Guage install

1) found the nipple at the back of the intake plenum

2) the clear pipe didnt fit (to small) so i cut the end of the black rubber cover and used that join the nipple and clear pipe (slid the clear pipe in and butted the nipple and pipe together)

4) fed through the firewall and tested

Is it possible that due to my connection it may leak pressure at anything above 0.4bar and therefor not read anything higher?

There doesnt appear to be any improvement in performance tho so im thinking its prob more the boost controller

any advice would be appreciated thanx

Lee

Link to comment
https://www.sau.com.au/forums/topic/99960-boost-guage-andor-boost-control-prob/
Share on other sites

hey ..well today ive "installed" a GFB manual boost controller and a boost guage ..

prob is weather the boost is turned all the way down or up shows no difference on the guage.

the max it shows on the guage is 0.4bar (5.6psi if my maths is right) pretty shitty!!

Boost control install..

1)i unplugged the 2 pipes from the standard solenoid

2)removed the T piece

3)replaced the pipe from the intercooler with the pipe that comes with the boost

controller (in case of standard restictor in the pipe)

4)basically put the boost controller in place of the T piece with the arrow facing towards the turbo

5)put a large screw in the end of the other pipe that originally went to the standard boost solenoid.

is this right?

Boost Guage install

1) found the nipple at the back of the intake plenum

2) the clear pipe didnt fit (to small) so i cut the end of the black rubber cover and used that join the nipple and clear pipe (slid the clear pipe in and butted the nipple and pipe together)

4) fed through the firewall and tested

Is it possible that due to my connection it may leak pressure at anything above 0.4bar and therefor not read anything higher?

There doesnt appear to be any improvement in performance tho so im thinking its prob more the boost controller

any advice would be appreciated thanx

Lee

Hi Lee, check the conection to the wastegate actuator. As per your other post, it looks to me like you have different connection to the wastegate actuator. The circuit should be like this;

I'C pipe------->Bleed valve-------->Wastegate actuator

:huh: cheers :(

Hey SK, cheers for the quick response

yeah its intercooler ----> bleed valve------> wastegate actuatator...

*scratches head*

no factory restrictors in place and the arrow is pointing towards the turbo :huh:

could it be the wastegate stuck or something along those lines?

Lee

Hey SK, cheers for the quick response

yeah its intercooler ----> bleed valve------> wastegate actuatator...

*scratches head*

no factory restrictors in place and the arrow is pointing towards the turbo  :(

could it be the wastegate stuck or something along those lines?

Lee

Hi Lee, stuck open wastegate actuator......hmmm......unlikely. Easy to check, give it a push with your finger. Or grab the vacuum pipe to the wastegate actuator and give it a blow, you can see the wastegate actuator lever move.

You should also check the bleed valve the same way (give it the blow through test). Make sure it is bypasing some airflow as you adjust it.

:) cheers :)

I am not sure what a GFB unit looks like, but on my 'Powerup MBC' I followed the instructions and had the same problem of not getting more then the standard boost. After stuffing around for a while connecting different hoses, I eventually took the MBC off and blew through the nipples while opening and shutting the valve, only to find that it worked the opposite way to the instructions. So if you blow thru the right connector you will feel a variation as you open and shut the valve and if you blow thru the wrong end it will have the same level of restriction no matter what position the valve is in.

My motor is a NEO and it has a three way T piece (with no built in restrictions): 1 - pressure in. 2- exit to the wastegate and 3 - exit to the solenoid. This 3rd hose going into the solenoid then has another hose going to the air intake pipe - this seems to me to be how the system controls the amount of pressure the wastegate sees by bleeding it off thru the solenoid. So all I did was pull the two pipes off the solenoid and attach them to the MBC (only opposite to the factory instructions) as per my blow test and whammo - variable boost.

cheers guys!! definatley worth a shot, i'll try that tonight if thats the prob could be a really good point for others to be aware of.

The pipe that normally goes to the standard boost solenoid (not the one from the T-piece) is the pipe that we put a screw into isnt it?? just checking but im sure the pipes are right

hahaa i just gotta laugh now, cos of the boost guage im now installing a single din head unit to make room for the guage underneath .. the aerial on the factory deck is nothing like a normal aerial, no matter what i try i cant get my circuit tester to light up to show me the positive and ignition hahaha.

excellent tutorial by alexcim on how to remove the head unit

Cheers guyz

Lee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...