recce

Alright guys! I have booked my car in for an inspestion on Monday with Dickson Motor Registry. FMIC, after market steering wheel (320mm) don't think that will pass, huge but not too nosiy Nismo muffler and everything else stock standard. Wish me luck.

Just have a look at the new intercooler and it does not have a nipple that pick up the hose to the actuator. Where do you guys tap the hose that goes to the actuator?

Rumble. Another question. Do we really need to change from NSW rego to ACT rego? Not sure how that works! If I have to go through that much trouble, I would better keep my NSW licence and keep my NSW rego. That really S#@Ks.

Rumble . When you say ID check do you mean the car ID check? Whats that!

Hi all! I have just change my NSW driving licence to ACT licence. The trouble with it is that I have to change my NSW rego to ACT rego. According to the "Shop Front" - ACT RTA, I have to get my car inspected by Authorised Inspected Station. I was given a list where to get it inspected. The question to ask is how tough is the vehicle inspection as I do have a front mount Intercooler and some other mods. Will that post any problem? Any comments!!

Sweet! I know that I need to trim the front bumber bar and has arrange the tools for that. Thanks mate!

Hi guys! Just bought an intercooler from Justjap and will be putting on this week end. Just wondering if I need to trim the front Reinforcement bar? I need to know so that I can arrange an angle grinder to do the job. Any help will be appriciated. Cheers!

Please PM me if anyone has any good used AC compressor for sale.

I got a XForce muffler for sale. It's a dual tip type (looks like standard muffler) with great exhaust tone. Very good condition. Asking $100. Pick up only in canberra. PM me if anyone is keen.

Is this cruise still going on? If so where in weston creek to meet?

Mate! Try powatone exhaust centre in Fyshwick. Don't know the price about SS dump pipe but I was quoted $450 drive in drive out for a 3" mild steel front dump. Ring them to see if they do SS. Their number is 62805217. Good luck.

Yes mate! The T piece is tap to the vac line. I guess the easy way to check it out is to set my boost controller to standard to see if I get 7 PSI. Id it does, all will be sweet.

Mate! It is not Auto Meter its Auto Gauge (I think chinese made). Do you mean the diameter of the restrictor? It is very very small. Couldn't tell but I think it is between 1 - 1.2 mm.

Anyone has got the Auto Gauge smoke face boost gauge? It comes with a "T" piece with build in restrictor and just wondering what does it do to the boost reading. Due to the larger "T" piece supplied by Auto Gauge, I did not use the "T" piece. Instead, I just use the old "T" piece from my privious gauge and now boost reads 1 PSI lower! Which reading should I trust? Anyone can help?

Mate! How much did you pay for the installation of your clutch. Mine is due to change and would like to know the price? BTW, where is gas tune located? Cheers!

Hi there! Just want to know what type of clutch kit you all used and the installation price in ACT? My clutch is up for a change and would like to know what I am looking @. Hope to run anbout 220rwkw. Cheers!

Hi there! Anyone got the same problem? When the engine is cold, cold weather it idle or start well. When the engin is cold while the weather is hot, it is sometime hard to start and will idle very bad for a short period of time (1-2min) and then goes ok? What is wrong? Same said that the fuel line swell during hot weather that causes that. Is That true? How do we grt around it and fix that! Any comments?

Thanks mick! I think I will save enough to get PFC.

Guys! Anyone know how much power gain can I get after installing and tunning of SAFC on R33 gtst running 10psi of boost. Some say 10-15 rwkw. Is that true?

Guys! Anyone know where to get a good Dyno tune in Canberra?

Cheers Mate! Will give Joe a ring.

Thanks guys! I think I will give garran (old tez) a try.

Guys, Anyone know what happen to Tez Automotive? I looked in the Yellowpages, found the number, spoke to the mechanic and he told me that the shop was longer call Tez? Is it still good to book my car for a service or check up (noisy engine)?

Any one have any stock GTR bov for sale?

Hi all! Just wondering if the standard GTR bov fits on R33 gtst (RB25DET)? Heard that it is better than the stock GTST bov and will not leak at high boost. Any feed back will be great.