Jump to content
SAU Community

craz0

Members
  • Posts

    551
  • Joined

  • Last visited

  • Feedback

    100%

Everything posted by craz0

  1. Wolf3D and standard still working on it.
  2. You can use them again unless they are totally stuffed. The rocker cover gasket's are made out of rubber.
  3. The battery that was in mine had Skyline R33 written on it, I just changed mine I got a Delkor 22F610D and got the terminals and the leads changed. Have a look here...http://www.skylinesaustralia.com/forums/sh...ead.php?t=28697
  4. No the problem I had with the Apexi was it wouldn't push the TPS signal to the Auto ECU but the Wolf3D does, I think the TPS just needs to be adjusted.
  5. I've just bought a V4 Wolf3D plug-in for my R33 GTST, I know it's a V4 Rev5, don't know about V4.55 :confused: It has gone in my Skyline a couple of times and I still haven't got it working properly as yet but I haven't taken it to get tuned in properly yet, my Skyline is a Auto and as far as I know the Wolf's don't have a problem with the Auto's. My Skyline is Standard other then a Jamex panel filter and the base Map didn't work with that, Steve-sst emailed me a Map and it worked, I just cant get it to idle as yet and I need to have my foot slightly on the accelerator to keep it at idle, when I let my foot of the accelerator it drops to just under 500rpm then conks out. We think the TPS might be a little iffy, have to check it out, haven’t had the time hopefully I’ll get to it soon and the Skyline want see a tune shop until after Christmas.
  6. The original is only about 270 CCA I think, does anyone else know for sure?
  7. Bump
  8. Put me down for a 910. When are you planning on doing this? how many people do you need?
  9. Anyone got some?
  10. I sent you a PM Steve. Thanks heaps
  11. Ta Autotrust
  12. I hooked up the Wolf 3D and it doesn't want to start everything seems to be fine, I pluged in the MAP sensor and nothing, the Injector lights on the side of the ECU dont flash at all. Anyone got any ideas? The picture attached does anyone know what it is? when I have the Wolf pluged in it you can hear it motoring away with the reds on but with the original ECU in it doesn't do it.
  13. I've got a R33GTST and I'm trying to find the Ignition switch relay does anyone know where it is? I done a search but come up with nothing. Thanks.
  14. And there is also the one up the back on the engine side that goes to you blow of valve.
  15. I've got a pic of the Battery installed if anyone is interested.
  16. Anyone got a pic of the under body of a Skyline (R33 preferably) showing what rod is what and what bush is what. For replacing suspension pieces. :aroused:
  17. It fits in the stock location but it doesn't fit into the little plastic thing that original sits on, the positive terminal just reaches but the negative is a little short not by much though and the original terminals are to small plus the hold down bracket isn't wide enough but one of them multi fit tops will fix that and there is another hole for the hold down bar to go into. I bought it from Mikeder Auto Electrics here in central Qld, they had a few different sizes I wanted the next one up thats made for a Cruiser but it wouldn't fit in between the metal guides:( but this one seems to be fine. I haven't installed it properly as yet I've done a dummy fit and it clears everything, I just want to get the terminals upgraded and the line extended a little to be on the safe side. Amp HR = 55 (20hr) Reserve Capacity = 90 (min) Cold Cranking Amps = 610 (-18deg c) Hope that helps.
  18. 230mm W x 190mm H x 170mm D $128.00 and what is a residual charge?
  19. Steve where is the best place to plumb in the map sensor on the plenum?
  20. Has anyone heard of a Delkor Calcium Battery? I just bought one for my R33 GTS-T. Model # 22F-610D Amp HR = 55 Reserve = 90 CCA = 610 It's also fully sealed. Just wondering what peoples thoughts where.
  21. What do you mean by "Try and get a clean plenum line if possible for the MAP"? Where did you get your line plumed into? Thanks GTS-t VSPEC
  22. So the MAP sensor has to be conected for it to work properly? so where is the best place to hook in the map sensor line? the fuel presure reg line? Can you still leave the AFM hooked up or do you have to remove that as well? My car is a 93 R33 RB25DET Auto everything is stock other then a Jamex filter in the original box and I run it on Optimax. Steve Taylor sent me the first draft of the Installation Manual for the R32/R33 GTST Plug-In ECU, I haven't had the chance to read over it yet and the manual isn't quite finished. Thanks heaps for your help. My Email
  23. Ok i got the wolf plug-in and I pluged it in and the car didn't want to start and when it did it coughed and farted and blow dark black smoke and the lights on the ECU looked like Christmas lights going of,so I turned it of :confused: don't know what happened here. The user manual I got with the ECU is for the normal Ver 4 but not the Plug-in version, I've contacted Wolf about this and I'm waiting on a reply. Steve-SST do you know if there is different versions of the plug-ins at all? mine has (rev 5) on it, also the PC software I got for it is Ver 4.49 what version are you currently using?
×
×
  • Create New...