Jump to content
SAU Community

Recommended Posts

looking to get a cage ive purchased fitted to my gtr (hks 6 point i think). have a few questions to ask as ive read some articles on here about this:

1. will i have to remove my rear seat as a result of having the cage?

2. in qld, are u allowed to have a full cage, i think its 6 point? in a street registered vehicle?

3. is a mod plate all u need to pass the rwc?

is there anything else i should know before trying to fit the cage??

thanking you all in advance :P

Link to comment
https://www.sau.com.au/forums/topic/100219-roll-cage-fitting/
Share on other sites

Yes

No (probably) Definately not in NSW

No you probably cant register it

Basically the front 2 points of the cage will make it illeglal since there is no protection for the drivers head against the bars.

Only rally rego allows a full 6 point cage. You need a 4 point "half cage"

you have to remove the back seat to fit it, but you can put the seat back in. not that easy to get back in though. i have a cusco t point cage and it is possible. however, it really destroys the shape (the foam) when you take it out again. having the rear cross bar made it worse for me.

i have full cage throughout my car. welded in. not bolted in.

went to get bluey - guy requested i get intrusion bars cut and shuffled to be removable. and pad the rest of cage. he said this would be enough for bluey.

i says ok..10mths later i havent done anything bout it.but anyway there is my experience.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...