Jump to content
SAU Community

Recommended Posts

Got a rb30 block sitting in my carport, was from a rb25/30 combo has all internals/sump (prolly rb25 sump as fins are trimmed to allow crank clearance), and water/oil pump. The bores have surface rust due the being open to the air. But if you going to rebuild it that aint going to matter anywho.

All the above for FREE!

I even have an engine crane to lift it on to your ute/trailor etc... need to get rid of it simply cause my dad getting sooky about is and saying:

All your sh!t is in the way!!

Which is so wrong cause his stuff takes up much more room lol. Either way has to go as i wont ever get around to using it.

Cheers

G

Edited by geordie
Link to comment
https://www.sau.com.au/forums/topic/100993-something-for-free/
Share on other sites

i'll take it please, can pick it up this afternoon.

can you send me your number, or call 0412 877 433.

thanks

Mark.

Sorry bud, was working all night. Will call you tomorrow morning (which may be closer to lunch pending on when i wake up :rolleyes:.

Cheers

G

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...