Jump to content
SAU Community

Recommended Posts

Yo, was hoping someone out there would be generous enough to share the power FC maps with me? if i can get someone with a similar setup to mine i can hopefully copy all there values into mine so it will just need fine tuning on the dyno & be close enough 2 drive it there aswell. might save me a bit of money 2!

Car is an A31 Cefiro with an R32 RB20det

Mods:

HKS Pod

3 inch exhaust

600x30x100 cooler & piping

Custom inlet plenum (copy of jun surge tank)

Garret GT25 400hp turbo (0.64/0.70)

tuned length stainless high mount manifold

tial 38mm gate.

GTR Fuel pump

550cc S5 injectors

Sard Reg @ 40psi

Still has RB20 AFM but looking for Z32

Power FC

Does anyone have a similar setup to this? maybe as long as you had 550 injectors & 2535 turbo or similar?? Would really appreciate someone posting up there maps

& before i get the beatdown i did search & read all 51 pages, learned a lot :huh:

Cheers guys!

Link to comment
https://www.sau.com.au/forums/topic/101589-calling-all-r32-power-fc-owners/
Share on other sites

Yep & it will be perfectly tuned to suit my setup, i was just hoping to get someone with similar mods to post their maps just so i can drive my car to the dyno. currently this is not possible. I realise it would be foolish to completely copy someones setup & leave it at that.

Anyone?

Cheers.

even with the 550cc injectors, z32 AFM etc.? it currently runs like a complete bag of shite! & trip to the dyno is about 1 hour away in peak traffic?

anybody want to share their maps with me?

Please! Please! Please!

Edited by Drift_Mulisha
The default maps will be good enough to drive it to the dyno.

:D cheers :D

.....with the injector correction set to about 49% it should be fine to drive to the dyno with the 0/2 feedback switched on

So as long as i set the injector correction to 49% it should be sweet to drive it there? this will be lost everytime i turn the car off right? Thanks for your help guys

p.s is there a particlar reason y people are not willing to part with the maps? is that cause they spent all that $$$ tuning it & dont wanna give it awway 4 free?

Dont mean to be rude, just curious thats all.

Thanks again!

So as long as i set the injector correction to 49%  it should be sweet to drive it there? this will be lost everytime i turn the car off right? Thanks for your help guys

p.s is there a particlar reason y people are not willing to part with the maps? is that cause they spent all that $$$ tuning it & dont wanna give it awway 4 free?

Dont mean to be rude, just curious thats all.

Thanks again!

No two engines are ever the same, even engines with mostly the same spec can require totally different tuning

It will take you hours to load my maps, you could leave before peak hour and get to the dyno in less time.

You may make a mistake in loading them, just one load point is enough (and there are a thousand or so).

They may run worse than the default, so you will have wasted your time.

They may run MUCH better than the default, so the engine feels like it doesn't need a tune. So you drive it hard, because it feels sooo great and goes sooo hard. But it was a bit too lean or too advanced and you blow up the engine.

All we are doing is trying to protect your investment.

:D cheers :D

Edited by Sydneykid

The injector adjustment will stay there all the time

There are two, the inj/ign where you can take timing out and add fuel, this will reset upon restart, and then there is also a injector window, where you can adjust lag time and correction, set this to 49% and turn your 0/2 feedback on via the etc menu and it should be driveaable

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...