Jump to content
SAU Community

Boost Gauge and Pillar Pods

Messiah

By Messiah,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

Al-R33 Enthusiast

Al-R33

Posted
Posted

Thanks Fry!

I found your pics and guide very useful!

Just thought I'd share what I did with my own install over the weekend.

For those who don't want to drill holes in their dash for the vacuum hose, you can run both the hose & wiring down a small gap where the door meets the pillar. This gap is large enough for the hose and electrical wiring, and does not crush or bend the hose when opening and closing the door. Just as an added precautionary measure, I wrapped the vacuum hose in some plastic piping from Supercheap. Even with the added thickness of the pipe, it still slid through the top gap in the door and out the bottom quite easily. Fasten it with some double sided tape or similar, and you're done! (just FYI I used stick on Velcro, also from Supercheap. This seemed to work the best for me).

On a side note I should also add that although the links to the pics in Fry's post don't work, you can right click and "Save Picture As.." just fine - the full sized pictures still seem to be on the server.

  • 3 weeks later...
Basti Grand Master

Basti

Posted
Posted
can the coppers defect you for havinga pillar pod installed?

iirc yes they can. i think the reason is that it can block vision. any guages or add ons need to be below the highest level of the factory dash. so DIN guages are cool but kinda crap cos you havta take you eyes off the road. i rekon the best compromise looks like the mearcat pods. looks as stock as possible

  • 9 months later...
  • 2 years later...
Guest

Guest

Posted
Posted

Good instructions, it's easier using the cigarette lighter power than working out other stuff.

Would like to add that the R33 GTR's don't have that hole in the firewall next to the stereo. Instead you'll have to cut open the large rubber grommet where the loom travels through, which is just to the right of the accelerator cable behind the insulating stuff.

Also I don't have the pillar gauge, just the one sitting on the air vent to the right corner of the dashboard, was best to run the vacuum hose down the vent and past the fuses and such.

Cheers

Ash

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      You Gregged a whole racetrack!?
    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...