Jump to content
SAU Community

Recommended Posts

Ok my baby is getting serviced today and tomorrow, just wondering how it will go when i get it back.

Here is what is getting done

injector service

major service

throttle body service

dual stage boost contoller

feul cut defender

new spark plugs 30 bux each

oil filter

feul filter

bleed valve

3inch zorst from turbo back

how does everyone think it will go when i get it back tomrrow avo

Link to comment
https://www.sau.com.au/forums/topic/10358-what-do-you-think-of-this/
Share on other sites

i will be runninig 14psi on high boost and around 8psi for low boost.

yeah the 3incher will work wonders i hope. its 180 for the plugs fitted so i guess they are the iridium ones.

Once all this is complete i will be getting a FMIC and a new turbo, dont know how big yet.

But for now this should get me around 160rwkw plus i hope

Originally posted by XXE-R32

i will be runninig 14psi on high boost and around 8psi for low boost.

yeah the 3incher will work wonders i hope. its 180 for the plugs fitted so i guess they are the iridium ones.

Once all this is complete i will be getting a FMIC and a new turbo, dont know how big yet.

But for now this should get me around 160rwkw plus i hope

with the stock cooler dont run 14psi, it will just get heat soaked and run like crap. Take it down to 12psi and it will run alot nicer.

Thanks for your Advice, i think i will run 12 INASNT and take your advice on that.

I will post up tonight to let you all know, infact i might be at cumberland maccas tonight if any of you want to come for a ride or have alook

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...