Jump to content
SAU Community

Recommended Posts

Item: 1996 Nissan Skyline R33 Series 2

Location: Geelong, Victoria

Item Condition: Excellent condition, Very Clean throughout

Reason for Selling: Just purchased a manual R33 so there is no need for the auto R33.

Price and Payment Conditions: $12,500 ono Looking for quick sale so all offers will be considered. Also I would be interested in swapping for another car and if necessary cash adjustments either way.

Details:

Nissan Skyline 1996 R33 Series 2 (2 door)

KMS: 92,410 Genuine

6cyl Non Turbo

Automatic Transmission

5zign cat back exhaust

White in Colour with full body kit

Nismo 400R Front Bar

GTR Rear Spoiler

GTR Side Skirts

GTR Rear pods

Features All Series 2 Interior and features:

Series 2 head lights

Twin Air Bags

Power Steering

ABS Breaks

Climate Control

Electric windows

Remote Central Locking

Electric Mirrors

Alloy Wheels

Alarm and 3 point Immobilizer

JVC KD S585 Head Unit

Just recently had fitted new:

New Radiator

Windscreen

Power Steering Rack

Tires

Break Pads

Will Supply with 12 Months Registration.

Will also come with R.W.C

The car has been well maintained and looked after and the car has been serviced and tuned regularly. The car has proven it self very reliable with no major mechanical problems and is very economical on fuel especially over weekly travel two and from Melbourne.

$12,500 ono OR interested in swapping for another car, just email me some info and pics of the car etc!

Contact Details: Luke on 0402650527 or e-mail: [email protected]

post-20589-1139746785.jpg

post-20589-1139746947.jpg

post-20589-1139747060.jpg

post-20589-1139747182.jpg

post-20589-1139747359.jpg

Edited by warby
the car in your avatar looks like his car that was for sale, he is from geelong.

nah different car, are you refering to the r33 with the abcent number plates? its the only other white r33 with a carbon bonnet that i can think of thats in geelong.

thats me your confusing warby with, yes his car looks similar to mine, to the point i keep getting everyone saying they saw me all over the place when I havent been. I've had mine for over 4 years now, an until warbys very neat 33 started being spotted over the last 6 months, mine was the only kitted white one with a carbon bonnet. Just a coincidence he even has dark coloured mags like mine.

just proves he has good taste i think.

Hey luke....sorry to whore your thread. hope that GT wing fit nicely on the Rx7.

i do have one question relevant to the thread.....why does the series 2 skyline have an SOHC engine in it? cant say i've ever seen one in a 33 before, is it a 2.0lt, 2.5lt, or 3.0lt engine?. does the rego sticker and the engine share the same engine number? or would it have to be changed over?

best of luck with the sale

Berin

Hey Berin, yeah our white cars with the carbon bonnets can cause some confusion, I have tried to modify my car as much a possible to make it look different as possible such as my do-luck boot, racing seats and i just got some East bear mirrors which hopefully arive soon. Trying to keep the white car, black wheels black bonnet theme. As for the rx7 i am still waiting for daltan automotive to finish all of the engine work and installing the microtech, so i havent had the chance to fit it yet.

As for the motor i am not quite sure because it is the same number on the rego sticker but i am not sure how big the engine is, as it looks like a vl engine but the guy i got it off said it was a 2.5 ltr. but i am not quite sure.

Ok to clear things up because i had a non turbo skyline exactly like this, except a 1995 manual.

the engine is this

Rb20E Sohc 1998cc.

It came in both Series 1, 1.5, and series 2 skylines. They were actually built this way, both manual and automatic, ive even seen 4 doors with these engines inside them.

Goodluck with the sale mate:)

Dayne

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...