Jump to content
SAU Community

Bling For Nissan's

300luva

By 300luva,
in Group Buys

 Share

Recommended Posts

300luva Newbie

300luva

Posted
Posted

Hi Guys, my first post up on Skylines Australia. Im selling GZA Dressup Kits on Aus300zx.com at the moment and they are doing quite well. Id thought Id give you guys the opportunity to buy at the same great price. These fit all Nissans that we have tested, Skylines, 350z and 300zx. Just make sure your caps are the same as them and your right.

here we go

Individual SPECIAL Prices:

Power steering cover for Hicas Z's w/wire - $30

Clutch reservoir cover - $30

58/80mm brake reservoir cover - $38.25

Radiator overflow cap cvoer - $30

Z logo battery tie down - $33

Z logo keychains - $15

300zx engine dipstick - $41.25

300zx transmission dipstick - $41.25

Radiator cap cover - $20

KITS

MANUAL $175 - PSteering, Clutch, Brake, Radiator Overflow, Radiator & Dipstick & Battery Tie Down

AUTO - $175 - Psteering, Brake, Radiator Overflow, Radiator, Auto & Engine Dipstick & Battery Tie Down.

POSTAGE is $10 Australia wide please deposit funds to: - WITH YOUR USERNAME

Nathan Grima

064-172

1013 9274

GZAss_dips.jpg

gzakit_at.jpg

P1011504.jpg

P1011501.jpg

Link to comment
https://www.sau.com.au/forums/topic/106699-bling-for-nissans/
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...