Jump to content
SAU Community

Vicroads And Legality Of Modifications


Recommended Posts

Yes but.... have any of them made a claim? What was the outcome? Also how do you decide if a mod caused an accident or not.. like.. ok I'm trying to think of a quick example..

Say you boost it onto the freeway, are not going over the speed limit.. and like in melbourne there is a really gay entrance to one of the freeways where everyone is trying to enter in two ADDED lanes and everyone else is trying to move to the left lanes to exit not too far up.. heaps of times trucks almost run me off the road because they dont look when they merge left... say I swerved to avoid a truck, lost it, ran into a pole.. say I had an upgraded turbo but no upgraded brakes.. you could possibly argue that if I had upgraded the brakes I might have been able to stop? I don't know, I'm sure someone else can think of a better example. The point is, it would be easy for an insurance company to find a million reasons to reject a claim and even Shannons has in it PDS that it only covers legal modifications.. You know I still haven't heard one story about someone who's had an accident and had heaps of illegal mods and got a payout.. :(

OK well I will use myself as an example, my car is fitted with non-permit and illegal mods yet I got paid out when my car was written off.... No mods to blame, purely driver error...

Its quite simple, if we cant PROVE that the 'illegal' mod was the reason for the claim, then it should be paid out.

Using your brake query as an example, proving that by not upgrading them caused you to hit someone is VERY HARD to prove, so most likely pay you out if all mods on the car were noted.

Its a very touchy issue, but atleast an insurer like Shannons wont write off the claim straight away like your regular insurers who hate to deal with imports, may....

actually the legal limt is 90db for cars after 1983. before that its 96db.

I have had 2 full epa tests done now at Macleod. I have had the car about 18 months but has effectively seen 5 months road time. First test stock exhaust got 90db 2nd time it got 89db (they have to round down). As for things like turbos, if you got low mounts you should be fine cos they wont really be able to see it. Using R34 N1's is good cos it looks like a stock turbo (bar a few different things like writing on the housings). The obvious things you will have to change though. So if you modify it yourself, keep the original parts like i have. Things like injectors, air box, ecu, exhaust.... Comes in handy!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...