Jump to content
SAU Community

Recommended Posts

Hi all

I machined at 4 discs, replaced the front pads (they were OEM Nissan) with Formula Ferodos, and rear (also OEM Nissan) with Bendix Advance.

I also flushed and bled the brake fluid with Castrol Response Super DOT 4.

I have not noticed any big increase in braking performance. ie. previously my car would take a bit to stop in city driving, as if the pads were not biting as hard. After this replacement, it has improved a little but not by much.

I have driven another GTT, and the pedal feels harder and pads seem to give a good first bite. A tap on the brakes and it starts biting. However after the initial bite, the brakes dont bite much harder. Nonetheless I noticed in my car that I actually have to step on the brakes for it to get that initial bite.

The vacuum in the brake boost is working fine. Any idea why my brakes dont have that good initial bite? My brothers Camry has a nice aggressive bite when tapping on the brakes. (OEM Toyota pads)

I have only driven with the new pads for around 80kms. Will they get better?

Note: I have not tested out high speed and hard braking yet as still want the pads and discs to settle in.

Edited by nuffsaid

In just 80k it's hardly likely.

I just checked the specs on Formula Ferodo and as they say consistent pedal FEEL from cold to hot, they also say OPTIMUM PERFORMANCE when brakes are warm. The Bendix Advance are just stockies, so you may be finding all the effective braking is being done by the rears.

I find it hard to believe you have either bedded the pads in or got them efficiently warm in the short didtance you have travelled unless on just one trip.

Maybe a different pad selection would be a better alternative, for day to day driving and keep your Formula Ferodo for the tough stuff.

That being said, I really have ZERO time for anything Ferodo, I find their after sales back up and warranty is not worth the paper it's written on. They will take any excuse they can to get out of any problem.

I have bedded the pads in.

Lucky I didnt spend money on Ferodo DS2500's then, coz they are even tougher than the Formulas.

Guys from Competition Braking said that the Formulas should warm up after a few stops. So I doubt they need warming.

Perhaps they need another 100km or so to settle in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...