Jump to content
SAU Community

Sold

r31 Koop
 Share

Recommended Posts

HKS-R33 Experienced

HKS-R33

Posted
Posted
I have sold my car so i now have no need for this turbo which i purchased last year.

The Turbo is an HKS T3G, which is what HKS now call the 25-30.

I am pretty sure it 350hp,(So good for 200-230rwkw)

It is based on the Garrett T28, as most of the HKS bolt on range are. (oil and water cooled)

Turbo has been freshly rebuilt, and has not been used since rebuild.

Lines and fittings are included, including a 3" Dump pipe, Braided oil line, water line banjoe bolts and the oil return line, with gasket, fittings and bolts.

So basically everything needed to bolt this turbo straight up to an rb20-25.

Im am asking 1100ono and would preffer a Melbourne buyer,

Thanks

Blair

0411 289 930

hey mate, is this turbo roller bearing?

Thanks, Mike.

Link to comment
https://www.sau.com.au/forums/topic/108588-sold/#findComment-2000747
Share on other sites
joorsh Enthusiast

joorsh

Posted
Posted
I gaurantee it has not been rubbing on the housing, Has not been used since rebuild and balance...

It is the light in the picture reflecting of some blades but not the others,

The black stuff on them is a bit of residue off the tape i have covering the housing. Part cleaner, or the turbo in action will blast that right off...

Yeah, I think you'll find the shaved section - or the bit on the wheel that looks like it has been rubbing - is actually the balancing marks. They shave tiny amounts off the turbine wheels to make sure they are properly balanced - this is perfectly normal.

Where abouts are you located?

Link to comment
https://www.sau.com.au/forums/topic/108588-sold/#findComment-2032691
Share on other sites
  • 3 weeks later...
  • 2 weeks later...
J_R32 Experienced

J_R32

Posted
Posted

how many kms ahs this turbo done, how laggy is it, and where is the power band? any shaftplay? and can u run this without ecu and injectors so long as u running standard boost, as a temporary thing?

Link to comment
https://www.sau.com.au/forums/topic/108588-sold/#findComment-2128025
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...