Jump to content
SAU Community

Recommended Posts

R factor is free to Down LOad you have to pay for it when you register, I have broad band but my Ozemail account its really slow 3kb's and i only have a 300mb DL limit:(

i'm just after the setup and installation files

M8 you didn't have to DL it i was after someone that already had it

Edited by Whiplash

well as i said the download is 688mb i have it now but dont u live down south

**EDIT**

ive used 58% of my monthly quota and im not about to use 4gb in 4 days since it a legitamate download i got no problem helping cept for the fact i dont have anything but DVD's to burn it on where about you work and maybee we can arrange sumthing

Edited by Madaz

Guys im noticings you are all pretty cluey i need some tech support i recently had this cpu in my MSI K8T Neo-FSR Motherboard ----- Athlon 64 3000+ 2000 MHz 512 KiB 800 MHz 10x 1.50 V 89 W Socket 754 ADA3000AEP4AX until i broke of one of the pins on a fan clean (bad story).

I got another cpu which i thought was just a desktop one but after changing power supplies and ram i noticed it was a Mobile one. Is this CPU my Problem??????? ------ Mobile Athlon 64 2800+ 1800 MHz 512 KB 800 MHz 9x 1.35 V Socket 754 AMD2800BKX4LB

DRIVING ME CRAZY

ps ( my comp problems were automatic reboot, memory dump, irq issues, stalling in bios setup)

Hope someone can help

Erin

what type of ram are you running it may even be driver issues

sum AMD chips require extra drivers

AMD Athlon™ 64/FX Processor Driver for Windows XP

if thast isnt needed im sure someone will say

More stuff to monitor your chip here the last few look ok like AMD Athlon™ 64 Processor Cool'n'Quiet Software

http://www.amd.com/us-en/Processors/Techni...71_9706,00.html

maybee your PSU is fluctuating in its volts and when it does your cou reboots

Edited by Madaz

I doubt the Mobile chip will be the cause unless its faulty.

I'm not sure how it is with the A64 Mobile chips but previously mobile chips are nothing more than a high grade desktop chip that is able to run high frequency's at low volts. So the item of choice for overclockers.

Have you tried the usual bios update, rip one stick of ram out, memtest etc?

lowered my 7950GX2 price to 650 dollars now. its brand new. thats a 110 dollar drop. details found in the For Sale section in the forums. RRP still around 1000 dollars and this ones new (4 weeks now) and never been OCd.

http://www.skylinesaustralia.com/forums/in...howtopic=143697

In regards to your problem. Can you state here what:

Motherboard

RAM

CPU

PSU

3d CARD

Hard drve

And then we will be able to have a slight clue as to what may be happening.

Edited by SAZilla

Skippy, I have a XP 3200+ you can have for $50 if it will get you out of a spot. Obviously no charge if it doesn't fix your issues - yes try before you buy. Comes with stock heatsink and fan, but will need new thermal paste. Let me know.

try doing this, if you have dual channel set up, take out a stick of ram, then if u installed the CPU yourself, make sure the fan is on correctly, might even be a heat issue for all we know. how many PCI cards, cd roms, hdds and what graphics card do you have. you problem could be a power/heat issue. causes alot of lockups.

do a bios clear by shorting a few designated pins on the motherboard with a jumper and then see if that helped. Look in your manual for the motherboard on how to clear the bios using the jumpers on ur board.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...