Jump to content
SAU Community

Recommended Posts

Just got my Creative X-fi extreme audio sound card. having probs installing.

Comp wont even detect the soundcard for some reason.

Win Xp.

anyone used these cards before ?

no diff between PCI 2.1 slot and normal pci and pci E ?

Just got my Creative X-fi extreme audio sound card. having probs installing.

Comp wont even detect the soundcard for some reason.

Win Xp.

anyone used these cards before ?

no diff between PCI 2.1 slot and normal pci and pci E ?

I've got the Creative X-FI Fatal1ty champion series , probably the same...

make sure you have power plugged into the back of the card , if thats in and its still not detecting , try a different slot.

have you disabled onboard audio via bios ?

Ive disabled via system devices etc. Might be something to do with the slot on the motherboard.

Tried other pci slot and nothing comes on the screen.

Will try disabling via BIOS

Shouldn't matter if the onboard is not disabled in BIOS because you should be able to switch between devices in Control Panel.

Just double check that it's seated correctly in the slot

As I stated above I was trying to install my new soundcard. So I can have some crisp sounds for music production.

after about 234 hours of stuffing around I became impatient.

Tried clipping what I thought was alittle power supply to the end of the soundcard. did this while the comp had power. Screen went all funny so i switched it of quickly.

Now when I turn it on I hear all the right sounds but have absoloute nothingness on the screen.

lost some music and im going to cry alitte bit.

As I stated above I was trying to install my new soundcard. So I can have some crisp sounds for music production.

after about 234 hours of stuffing around I became impatient.

Tried clipping what I thought was alittle power supply to the end of the soundcard. did this while the comp had power. Screen went all funny so i switched it of quickly.

Now when I turn it on I hear all the right sounds but have absoloute nothingness on the screen.

lost some music and im going to cry alitte bit.

its not likely you've lost your data

reset the CMOS, you may have only screwed the bios settings

-D

Will try that.

Just dont want to go near the other comp for a few mins. It may end up on the road or in the oven.

I was looking around for maybe a small fuse I may have blown ? Dont some motherboards have em ?

As I stated above I was trying to install my new soundcard. So I can have some crisp sounds for music production.

after about 234 hours of stuffing around I became impatient.

Tried clipping what I thought was alittle power supply to the end of the soundcard. did this while the comp had power. Screen went all funny so i switched it of quickly.

Now when I turn it on I hear all the right sounds but have absoloute nothingness on the screen.

lost some music and im going to cry alitte bit.

OK so you hear a single beep when you turn the machine on and you get fans/hdd's spinning but nothing on your monitor.... At worst you've fried the graphics card. If nothing is happening (after what SLED has already advised) then you might have fried the Power Supply. Having re-read your post ^, there is a difference between PCI Express and PCI 2.1. PCI 2.1 slots are usually white slots on mobos and have a largish edge connector, most if not all PCI cards are compliant with 2.1. PCI Express cards have a very short edge connector and slots are usually black.

Also if you ever need any help/advise in regards to computer music production feel free to PM me... I've been doing this stuff for far too many years and have built and configured many digital audio workstations. If you don't mind me asking, how much did you pay for the creative card?

Still nothing.

hmm'''

I took out the Video card and went to onboard. Still nothing. so its not the gpu.

How exactly do you reset CMOS> maybe im doing something wrong.

I install all my own parts and never had this prob. its fkn annoying.

How exactly do you reset CMOS> maybe im doing something wrong.

There will be a jumper switch located near the CMOS battery or between the pci slots - your motherboard manual schematic will point u in the right direction

download it off the net if u havent got a hardcopy

simply move the switch from position one to position two and back (while the unit is off)

same goes with jumper pins and jumpers, it'll be located near the cmos battery

yes there are fuses, but theyre located inside the power supply - i dont recommend you open that up due to the capacitance and AC current

-D

How exactly do you reset CMOS> maybe im doing something wrong.

I install all my own parts and never had this prob. its fkn annoying.

Easiest way to reset the CMOS is just to pull that button battery out from the mobo & leave it out for a bit & put then put the battery back in, that should clear up what ever settings were stored.

Alternatively depending on your mobo model, there is a specific jumper pin you have to set to reset the CMOS (have to read your mobo instruction manual for that). Some of the higher end spec mobos have a switch/button for it, instead of a jumper.

Good luck with it.

On a different topic, my GTX-260+ card just arrived in post today :D

EDIT: got beaten to it.

Edited by Mayuri Krab

Intersting. Usually when something like this happens at the end I always think Ive learnt something.

Tonight I havent.

Put the 9800gt gpu back in. Nothing.

Tried cmos battery method again. nothing.

Tried cmos jumpers. nothing.

I just cant put my finger on it.

That last screen I saw b4 all this happened did look pretty scary. Prolly fried something .

I even Tried clicking mouse buttons etc while the thing was running just to hear the HD running thru cycles. nothing again.

Intersting. Usually when something like this happens at the end I always think Ive learnt something.

Tonight I havent.

Put the 9800gt gpu back in. Nothing.

Tried cmos battery method again. nothing.

Tried cmos jumpers. nothing.

I just cant put my finger on it.

That last screen I saw b4 all this happened did look pretty scary. Prolly fried something .

I even Tried clicking mouse buttons etc while the thing was running just to hear the HD running thru cycles. nothing again.

well start with the obvious. change the power supply unit to another one, if its a matter of voltage regulation or fuses you'll know straight away...

next thing would be your motherboard but you'd have to find a place that has a spare thats compatible with your cpu and ram to eliminate that variable.

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi from Canada, Both of my calipers are starting to fail. My car is a 2005 M35 Stagea ARX and I can't seem to find any parts or any cross reference caliper that would fit my car. Is there a company or a similar caliper that would fit and I could replace the OEM one. Or if anyone knows where I can find a new OEM. Any help is very appreciated. Let me know!
    • Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • 🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
×
×
  • Create New...