Jump to content
SAU Community

Recommended Posts

Hey guys, just posting up my bluebird to see what people will offer me,

im also open to swaps.

original owner had car dyno tuned n it made 278 on 11 psi, engine capable of holding 25PSI comfortably.

Car has Custom plates on it(JET FJ) Black on yellow

car has had over 40k spent on it.

List of Modes:

ENGINE

FJ20 Turbo built by V&E Rigoli in April 2004 done about (12000kms) since build.

Standar five speed Excedy Heavy duty clutch

Forged wiseco pistons, malloy rings, new conrods, crank shotpeened and balanced.

Hi-Flowing T3 Turbo built by Precision Turbochargers capable of 450hp.

Huge polished front mount intercooler

3inch stainless exhaust from turbo back brand new cat.

Microtech MT8 ecu and hand controller.

Turbosmart adjustable incabin boost controller.

Has 1 nissan GTR Fuel pump and lift pump, will sell with brand new Bosch 600hp pump and brand new carter black lift pump and Malpassi fuel reg i also have a solid 3/8 fuel line for fuel in-line.

The car runs 616cc injectors on the standard fuel rail

Pod air filter

EXTERIOR/INTERIOR

Custom orange paint

Custom front bar

Cosworth bonnet vents

Tinted windows

Custom leather interior With Skyline front bucket seats (seats, doors n roof trimmed)

Sparco leather steering wheel

Autometer monster tacho, boost gauge, oil pressure

17 inch gold lenso 7 spoke rims.

Two new tyres and two bold tyres.

Sound system

Kenwood cd player

7/10 kenwood speakers

2x6inch speakers

make me an offer n we'll go from there..

Untitled-1.jpg

JETFJRear.jpg

JETFJFrontRight.jpg

JETFJ.jpg

A11.jpg

A10.jpg

A9.jpg

A8.jpg

A7.jpg

A4.jpg

A2.jpg

A1.jpg

Looking to trade for R32 or R33,

but still open to other offers

Edited by AznBikerBoi
Link to comment
https://www.sau.com.au/forums/topic/108960-nissan-bluebird-fj20et/
Share on other sites

no i dont want to, thats why i said make an offer, obviously!!!

open to swaps!!!

$1500 then, as well it is only a blue bird...

That is why they ask for a price. To save people wasting YOUR time with stupid arse offers. Work out what you want for it, add $1-5k to that price, done, easy.

$1500 then, as well it is only a blue bird...

That is why they ask for a price. To save people wasting YOUR time with stupid arse offers. Work out what you want for it, add $1-5k to that price, done, easy.

ok personally i dont c the point of doin a price range thing, like i were to say, ok im chasing 7-13k, OBVIOUSLY ppl are gona offer 7k.

but im sure people are smart enough to offer abit more then 1500.

Put up some price. It's the rules. Your thread will be closed very shortly I'd say.

Common sense says you put up your higher preferred price and work your way down from there.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...