Jump to content
SAU Community

Recommended Posts

garage cleanout time

r33 s1 rear pod--drivers side 50$ -SOLD

r33 s1 cam gear/timing belt cover 50$

r33 s1 plenum + crossover + turbo pipes 100$ -SOLD

r33 s1 standard computer 200$

r33 s1 dash 80$

r33 s1 radiator + shroud 100$----sold

r33 s1 coil cover 20$

s1 rb25det cams 200$ --SOLD

r33 s1 floor mats front and back middle mat 80$ -----SOLD

r33 s1 bonnet wine red 200$

r33 s1 wing 100$

r33 s1 drivers side mirror 80$

r33 s1 washer bottle 30$

r33 s2 air box 50$---SOLD

r33 s1 right indicator 20$

r33 s2 steering column 2 pak silver 60$

r33 s1 exh cam gear 50$

r33 s1 right back seat interior panel 50$---cloth trim removed

r33 s1 left side back floor matt 10$ cant find other one yet...

r33 s1 standard side winkers 30$

r33 s1 clock demister hazzard sidemirror controls 50$

ignore circles in bonnet pic...shitty flash on cam..

Edited by thizzle
Link to comment
https://www.sau.com.au/forums/topic/112054-r33-gts-s1-s2-garage-cleanout/
Share on other sites

What colour is the drivers mirror? is it convex or straight glass?

the mirror is gold/green but its been scraped off a bit as u can see the wine red under it...

i couldnt handle havin no mirror while it got repainted so i bought one from sss auto..its glass.

Edited by thizzle

80$ cuz i cleaned all that film that peels on s1 off it so now its perfect for paint

all vents included plus buttons + clock are round some were 2..

60 just for the dash if u pay shipping

Edited by thizzle

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...