Jump to content
SAU Community

Recommended Posts

I have almost completed my rebuild of my 32 gtr, it is sitting on the hoist at the moment and i am scratching my head as to where the so called "air bleed plug" that the service manual says to pull out to get constant hydraulic pressure to bleed the 4wd is, i have searched in the boot and under the car to no luck, if someone could point me to where it would be that would be great, the manual says "lower dash side" on the location and the plug is supposed to be white or something, thanks!

Link to comment
https://www.sau.com.au/forums/topic/113825-attessa-4wd-help-plz-bleeding/
Share on other sites

I have almost completed my rebuild of my 32 gtr, it is sitting on the hoist at the moment and i am scratching my head as to where the so called "air bleed plug" that the service manual says to pull out to get constant hydraulic pressure to bleed the 4wd is, i have searched in the boot and under the car to no luck, if someone could point me to where it would be that would be great, the manual says "lower dash side" on the location and the plug is supposed to be white or something, thanks!

Its a white connector behind the driver kick panel next to the accelerator pedal.

you don't need to worry about the white plug....just put the car up on stands, start the car in neutral....anytime the engine is running there is pressure in the attesa system.

then there are 2 bleeders, one at the rear of the transfer case and another bastard above the rear drive shafts.

The bleeding is dead simple, easier than brakes because the fluid is under pressure.

Make sure the resoviour in the boot is full, then with time the motor is running, put a piece of clear pipe over the bleeder (same as brake line) and open the bleeder. Let the fluid come out until there are no bubbles. Do it up again.

See....easy :D

<bump>

I wanna bleed the attessa in my car. It doesn't look terribly complicated, but I would *really* appreciate a couple of pics in a "howto" thread.

Oh - make sure you include a suggestion (or three) about appropriate replacement fluid.

I just don't quite have the confidence to try it without pics.

Thanks

nK

nicholas Krul

No worries, ill do the DIY when i have the car at my mechanics, which will be very soon as i have to have it ready for a track day on the 29th of this month

Ill take loads of pics for you and the other guys who feel the same way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...