Jump to content
SAU Community

Recommended Posts

i have a set of blue race seats to sell non reclinable they are daytons light as a mofo great condition with rails unversal wont take much at all to fix to a r33 ill have pics up later tonight these are comfy

post-17846-1145545594.jpg

asking $350 firm

plus postage can get freight cheap great condition

Edited by teazn_r33
Link to comment
https://www.sau.com.au/forums/topic/114331-race-seats-cheap/
Share on other sites

i have a set of blue race seats to sell non reclinable they are daytons light as a mofo great condition with rails unversal wont take much at all to fix to a r33 ill have pics up later tonight these are comfy

post-17846-1145545594.jpg

asking $350 firm

plus postage can get freight cheap great condition

what do they each weigh?

what's freight to perth?

what are they made from,how rigid structurally?

cheers

  • 2 weeks later...

i had 1 of these in a previous car i was very shocked in how comfy they are i have broad shoulders n was tuff to find a seat that fitted well, i also checked and believe these are ADR approved!! make sure but i think theres a sticker on the bottom! unsure if rails are ADr approved tho

sorry pplz im in mildura vic but i can say that im a 6ft lad that weighs 100 kilos with a nice round gut "well paid for" and i fit in them with ease very surprising these are a good seat and ill have som more pics if you want tomorro

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...