Jump to content
SAU Community

Recommended Posts

Hi guys, I'm a proud new owner of a 96' r33 gts-t. Just got it a few days ago and its been driving great! One thing though, I've been experiencing times where the HICAS light would come on after driving for some time.

Tried to do a search to gain more information in the forums but somehow no one has explained if it was a big issue to have that light or not. Could anyone help me with this? Should I get it repaired? If so, how much would it cost? Thanks.

Edited by blu3chip
Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/
Share on other sites

could be a number of things wrong with it...have you checked your power steering fluid? have you got a smaller steering wheel?

No, I haven't done anything to my car. It only seems to happen after I drive at high speeds or for some time.

Edited by blu3chip
Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2113298
Share on other sites

I have had exactly the same problem.

I bought a S2 R33 GTST about 3 weeks ago with 57k on the clock. Everything is perfect except that the HICAS warning light comes on after driving for a period of time. I logged the time from starting the car and kms until the HICAS light comes on and found that it was dependant on distance travelled only, with the light consistently coming on after exactly 10 kms whether driving on freeway or twisty roads below and above 80km/hr. Time travelled varied in each case and had no effect on whether the light would come on or not.

To clarify, when the HICAS light is on, it means that the system is disabled and 'normal' steering (front wheels only) is in operation. I have also attempted to run the diagnostic procedure in the skyline book from this website but have not even been able to get it into diagnostic mode (ie car operates as normal, no flashing error codes from HICAS light). I have also taken the car back to the dealer twice and they cannot find any problems, also having the HICAS control module replaced has not fixed the problem.

If anyone can shed any light on specifically getting the Diagnostic mode to work that would be good.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2120119
Share on other sites

Do the search. We don't like regurgitating this every 3 months.

I have used the search heaps, sometimes you can get some good results and sometimes not. I did find one possible solution regarding aligning the steering wheel and checking the steering angle sensor which I will try. I thought I would still post anyway seeing as though most of the time the problem isn't clearly defined (ie what causes light to come on, under what conditions and is it consistent), also the answer nearly always is to just get rid of 4ws, but I would prefer to keep it working as I don't race or drift.

Edited by R.C
Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2122499
Share on other sites

Well there is very detailed information you both have offered here so we have to play the guessing game again!! There are just a few hints that you could offer like:

aftermarket steering wheel or not (as HICAS uses a special boss to turn the steering position sensor)

is the steering wheel aligned centrally when you drive

is there the same number of turns from centre to lock on each side

HICAS also warns of low PS fluid in R33

Just anything odd or non standard to do with steering.

If all else fails either:

a) leave it and hope it doesn't make the rear act up, or

b) lock it, but don't ask. I have none left until later in the year.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2122592
Share on other sites

Thanks for the info.

In my case all steering components are standard. Have checked the P.S fluid and all electrical connectors and steering is straight when on flat level road. Also my car has a 3 year 3rd party warranty and 3 month dealership warranty so I am not paying for anything hence why I am trying to get it fixed. The only problem is I don't have that much confidence in the mechanic who is looking at it (having taken it back twiced to no avail) so I am trying to help find the cause myself.

Appreciate your input.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2123578
Share on other sites

Thanks for the info.

In my case all steering components are standard. Have checked the P.S fluid and all electrical connectors and steering is straight when on flat level road. Also my car has a 3 year 3rd party warranty and 3 month dealership warranty so I am not paying for anything hence why I am trying to get it fixed. The only problem is I don't have that much confidence in the mechanic who is looking at it (having taken it back twiced to no avail) so I am trying to help find the cause myself.

Appreciate your input.

R.C, we seem to be having the exact same problem. My HICAS light comes on after 10-15km's of driving continuously though I've not done/changed anything to try to fix it. My problem however, should be able to be fixed with a change of the PS fluid as mine is filthy now. Do let me know if you've managed to verify the problem though as it seems like we're on the same path. Cheers.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2128405
Share on other sites

R.C, we seem to be having the exact same problem. My HICAS light comes on after 10-15km's of driving continuously though I've not done/changed anything to try to fix it. My problem however, should be able to be fixed with a change of the PS fluid as mine is filthy now. Do let me know if you've managed to verify the problem though as it seems like we're on the same path. Cheers.

Seems like this is a very common problem for a lot of people!

I did take the car back to the dealer on the weekend and got the mechanic to look at it while I was there. We took the steering wheel apart and looked at the s.w angle sensor and found a couple of faults. The soldering on the circuit board of the sensor had a few dry joints as well as a broken track. These were fixed and put back together only to find the HICAS light still coming on when I drove home. I'm not totally convinced that that wasn't the problem still only because the sensor itself wasn't replaced, something else may have been wrong with it. I still could not get it into diagnostic mode (either could the mechanic) so maybe the sensor is not working at all - ie it does not detect me turning the wheel when trying to enter diagnostic mode?

It's really starting to annoy me now.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2128767
Share on other sites

My friends car is having the same problem.

Its an series 1 R33 and when the hicas light comes on, the steering becomes really heavy, as if the power steering is gone.

The car has recently been in an accident where the rear suspension was damaged as it slid out into a gutter. It has all been fixed, replaced though. Could this just be fluid or something with the Hicas system itself.

No mechanic has so far been able to figure out whats goin on.

Anyone recomend a Mechanic good with skylines in the sydney area?

cheers

Edited by aym23q
Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2133018
Share on other sites

I had the HICAS light come on when driving the car home along the freeway after about 5 or 10 minutes, and it didn't go off until after I got home and switched off, even after getting off the freeway and into stop-start traffic.

I topped up the power steering fluid which was below the low mark, but the steering was never heavy before or after. I haven't had the problem since, but also I've never travelled as far at highway speeds yet. Also my steering wheel is off-centre but I would think if that's an issue the light would still come on regardless.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2137350
Share on other sites

  • 2 weeks later...

Update - 1 HICAS problem solved.

After taking my car back to the dealer for the 4th time it looks like I finally have the HICAS problem licked. My initial thought was that it was the steering angle sensor which turned out to be correct. The first clue was that it would not go into diagnostic mode ever, which made me think that it wasn't sensing that the steering beeing moved at all. Anyway, I took it back and told them to replace the sensor (which they attempted to 'fix' last time).

After replacing the sensor and then attempting to enter HICAS diagnostic mode it finally worked, HICAS light flashing signifying no fault, rear wheels entered test sequence turning left and right. The car has been driven on a few trips of more than 10 k's since then with no problem showing up, so it looks like this has fixed it.

LESSON: If your HICAS is playing up (light coming on in dash) and you cannot enter diagnostic mode, one possible cause is faulty steering angle sensor. The light will come on after 10km if it does not sense that the steering wheel has turned.

Link to comment
https://www.sau.com.au/forums/topic/114704-hicas-light/#findComment-2188896
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...