Jump to content
SAU Community

Hicas Weirdness

123456
 Share

Recommended Posts

123456 Proficient

123456

Posted
Posted

This problem has been happening some weeks (has a couple of posts about it but i can seem to get on my other login), andyway ill be driving then suddenly my steering gets very heavy (before hand it is perhaps lighter than normal) and after some minutes my HICAS light turns on. Then i turn the car off and on and have normal/light steering for 30 seconds - 10 minutes before once again it gets heavy again. I noticed now that it seems to only happen when i have over half a tank of fuel. A full tank meaning it occurs most often and a half full tank or less meaning the problem occurs never or not often.

Any help would be appreciated because at the moment i am trying to save up for a tune up and dont want to spend money trying to fix the hicas

Also i noticed tomei has a kit on the nengun site which disables the hicas electronically and mechanically and doesnt require more work than some wiring. Would installing this be likely to fix the problem

Thanks

Link to comment
https://www.sau.com.au/forums/topic/115007-hicas-weirdness/
Share on other sites
123456 Proficient

123456

Posted
  • Author
Posted
30 minute installation, a $150 lock bar and a wheel alignment and u'll never have to worry about the HICAS again ;)

Uhmm yeh i didnt really like the idea of installing the lock bar though. Was hoping that tomei one would do the trick ahhh.

Any other suggestions from any 1 at all which would help solve the problem would be verrry much appreciated

Link to comment
https://www.sau.com.au/forums/topic/115007-hicas-weirdness/#findComment-2118149
Share on other sites
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...