Jump to content
SAU Community

Suspension Coilover Makes Squeaking Noise.

RBFIRE
 Share

Recommended Posts

RBFIRE Experienced

RBFIRE

Posted
Posted

Hi,

Just bought myself a set of used Apexi Coilover, always a catch,

on the passenger rear side suspension, making squeaky noise, sound like something rubing against it, metal to metal.

its sound exactly like when u jump up and down on a springs bed (hope it describes better). made noise when driving or stand still and u push against it.

Does it means its on its way out?

3 of 4 shocks was fine, no noise.

problems after problems, feeeling so low.....

any one have any ideas?

thanks.

foznice Veteran

foznice

Posted
Posted

I *think* i have the same noise as you... almost like a scunching sound? except I have stock damper and spring setups, and it's on all four corners, the sound has only come out recently, and it's only heard when it's under a fair bit of load, like speed humps, coming in and out of my driveway (over a smooth curby type thing) and taking round abouts with a little bit of speed....

I can't tell any handling differences as such, at least from general lowspeed manouvering on the steet (apart from this noise of course)

does anybody know what this is?

RBFIRE Experienced

RBFIRE

Posted
  • Author
Posted

the noise only come from 1 coilover, so i thought something is wrong.

performance wise, cant tell, but its quite annoying!!!

though mines squeaks on un even roads as well.

guess that is why its cheaper than NEW!!! ;p

tried to spray wd40? lol, onto the top rubbber mount, but NOPE, noise still there.

probly will try to swap to its original spring,

see if it goes away,

the previous owner reckon the Apexi spring is bit harsh for the road, so he replaced it with a softer springs for the rear.

Its not too bad, noise will go away if window is down. But am chasing for perfections!!!

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...