Jump to content
SAU Community

Recommended Posts

Ok guys just want to know how to change my fuel pump as I dont know how to dismantall bits and pieces surrounding to get to it . As I have pulled back seats out with no success and also taken off back shelf in boot with no success and undercar looks like best bet but dont know how.

Could someone pls help as I'm in need........

Thx In Advance

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/
Share on other sites

dont kno about r34s but on r32s the fuel pump is located in the boot, u just take off the plate an a few other screws and i comes out.

Nah the 34 is different I think as there is some sort of round thing in boot but cant seem to c fuel pump.

Pls Guys some help as car is ready to be tuned........ :O:)

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2153044
Share on other sites

Yes you go through the boot.

It's on that shelf part on the drivers side.

There is a metal plate with 4 10mm bolts. Take that off then you will see the top of the tank.

Use a piece of wood and a hammer to get the round plastic cap thing off after you remove the hoses.

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2153401
Share on other sites

Yes you go through the boot.

It's on that shelf part on the drivers side.

There is a metal plate with 4 10mm bolts. Take that off then you will see the top of the tank.

Use a piece of wood and a hammer to get the round plastic cap thing off after you remove the hoses.

I did that but dont know how to get the actual fuel pump out??????????

Is there a procedure for getting it out?

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2153877
Share on other sites

The stock fuel pump is mounted on a "gold" bracket... it is set at an angle into the fuel tank (about 45 degrees). Take your shirt off and reach down into the fuel tank you will be able to reach the pump easy.

From memory, the bracket just slides off it's holding plate with a firm tug - there are no bolts holding it in.

NOTE: Make sure you don't have any sparks or lights shining down there... don't want a fire starting now do ya?

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2154046
Share on other sites

Which pump are you putting in... I hope you have a direct replacement otherwise you're in for a little surprise :ermm:

SHit Dont tell me that I have already have enough surprises!!!!!!!!

I am putting in a Bosch 040!

Does it slide up or something?

Pls tell that this will be ok :ermm::)

Edited by wrxxy
Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2154132
Share on other sites

Thanks for that Bob...

Yes as my sidekick has mentioned it slides straight up...

The Bosch 040 sucks from the bottom of the pump, the stock pump utilizes a "sock" which reaches all the way to the bottom of the tank.

Now here's the choice you have to make;

1) Somehow fix the 040 to the bracket (I had to modify mine) and make a custom extension to the bottom of the tank - you will need a reducer made up and some thick silicon hose that goes to the bottom.

2) Extend the fuel hose and just drop the pump into the bottom of the tank. You may get some "noise" :ermm: But with a little bit of thought, you can get around this.

I went for Option 1) as it seemed like the better one to follow (at a cost of course).

If I was to do it again, I would get the Nismo or Tomei drop in's or use the stock pump and run it into an external pump + surge tank setup.

Cheers

S

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2154182
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you are Ecutek tuned then these TCU tunes are anywhere from $550 to $700 usd. If you are not ECUTEK tuned, then it gets costly!    
    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
    • Cats are called Bella, and Donna...  Like that poisonous plant And I remember your 2 monsters, I remember making a little bit of wee when you let them out... LOL I have already installed cat doors into the laundry where their kitty litter is, and the sun room, apart from the cat doors there's not going to be any permanent mounted stuff on the interior walls (interior doors are cheap and easy to replace) I will get a outdoor cat cage thingie once I finish the landscaping out back... https://catnip.com.au/ The only off limit areas are the main bedroom and the gym room....but, currently the cats are curled up in bed, in the main bedroom with the Mrs.....LOL, the off limits for the kittens to the main bedroom lasted about 5 minutes with Jackie I currently only have 1 free standing huge cat tree multiple level scratching post thingie in the lounge room, but, I will be getting another one soon now that I'm happy with the furniture layout in the back room and have a perfect spot for it  
    • All of this is making it seem clear that running the Coppermix twin was definitely the way to go, especially in hindsight with how insane tariffs have gotten and the strength of the USD vs yen at the time.
    • That sounds like no chance of even importing one for road registering then Now I see why Duncan wants to check LHD rules for Targa...   I wonder how "bolt in" the AWD would be if you got one imported from the US and swapped it to an AUD one
×
×
  • Create New...