Jump to content
SAU Community

Recommended Posts

I want to get the fuel pump out my tank and have a quick look at it and see whether the internal filter needs cleaning.

How do I go about this? Do I have to drop the whole fuel tank out and remove it from the top?? I have seen in some other cars there is an access panel from say the boot or whatever that makes removing it pretty easy without pulling the tank out - anything like that on the R33 ?

Link to comment
https://www.sau.com.au/forums/topic/11783-removing-fuel-pump/
Share on other sites

no tank dropping required whole assembly comes out through the boot

acess pannel in the boot

then unscrew the plastic cap and remove assembly from in tank

i did this once but i dont recomend doing this it is a dangerous procedure and the whole boot fills up with fuel vapours

one spark and boom you now have no face

aswell as the bad effects fuel vapours can have on your lungs

after 5 min of fiddling inside the tank i was completely ****ed up

i had no idea how high you can get on fuel vapours

not a good high mind you killer headache and loss of balance

and also

spinnin`...

spinnin`....

spinnin`

make it stop

hehehe..mygtst - I don't intend on standing there inhaling the stuff to get high :) I'd take it out in the open and like v-spec said make sure most of the fuel is out of it first.

I know petrol is smelly stuff. Shoulda seen when I changed my fuel filter.. petrol dripping everywhere ..and i did that in the garage :D

So where is the panel? I had a look in the tyre well and couldn't see anything. Is that the plate near the fuses and battery behind the rear seat (yes, remove battery first, safety first, blah).

predator.. haehaeh wat a co-incident. i was thinking about the

same thing and gave it a try...

what MYGTST said is right. well right from what i could see.

the cap is soo hard to turn cause of the rubber seal. once i pulled

it open the pump sat all the way down at the bottom so i suggest

emptying it as much as possible.

I'm not sure how to take the pump out tho.. it was very cramped

for me.. Let me know how u go.

...more to the point - how does it go back? apparently it sits at the bottom of the tank face down and sucks. If I just pull it out I might not be able to put it in the proper position - causing major probs for fuel sucking.

the pump sits on a metal bracket which is clipped in place all you have to do is unclip the metal bracket and it comes out with hoses and attacments

the pump is clamped to the bottom of the bracket so you simply clamp it back in the same place once your done

to remove the assembly you need to feel inide and slide the bracket up and to the side and it unlocks

the access panel is in the raised section of the boot on the right hand side and yes the plastic cap is a pain to get off its so tight

i recomend removing the battery from the car during tank opening

less chance of sparks

byt he time you figure out the how the bracket comes out you will be well and truly high even if your tank is almost empty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...