Jump to content
SAU Community

Recommended Posts

I want to get the fuel pump out my tank and have a quick look at it and see whether the internal filter needs cleaning.

How do I go about this? Do I have to drop the whole fuel tank out and remove it from the top?? I have seen in some other cars there is an access panel from say the boot or whatever that makes removing it pretty easy without pulling the tank out - anything like that on the R33 ?

Link to comment
https://www.sau.com.au/forums/topic/11783-removing-fuel-pump/
Share on other sites

no tank dropping required whole assembly comes out through the boot

acess pannel in the boot

then unscrew the plastic cap and remove assembly from in tank

i did this once but i dont recomend doing this it is a dangerous procedure and the whole boot fills up with fuel vapours

one spark and boom you now have no face

aswell as the bad effects fuel vapours can have on your lungs

after 5 min of fiddling inside the tank i was completely ****ed up

i had no idea how high you can get on fuel vapours

not a good high mind you killer headache and loss of balance

and also

spinnin`...

spinnin`....

spinnin`

make it stop

hehehe..mygtst - I don't intend on standing there inhaling the stuff to get high :) I'd take it out in the open and like v-spec said make sure most of the fuel is out of it first.

I know petrol is smelly stuff. Shoulda seen when I changed my fuel filter.. petrol dripping everywhere ..and i did that in the garage :D

So where is the panel? I had a look in the tyre well and couldn't see anything. Is that the plate near the fuses and battery behind the rear seat (yes, remove battery first, safety first, blah).

predator.. haehaeh wat a co-incident. i was thinking about the

same thing and gave it a try...

what MYGTST said is right. well right from what i could see.

the cap is soo hard to turn cause of the rubber seal. once i pulled

it open the pump sat all the way down at the bottom so i suggest

emptying it as much as possible.

I'm not sure how to take the pump out tho.. it was very cramped

for me.. Let me know how u go.

...more to the point - how does it go back? apparently it sits at the bottom of the tank face down and sucks. If I just pull it out I might not be able to put it in the proper position - causing major probs for fuel sucking.

the pump sits on a metal bracket which is clipped in place all you have to do is unclip the metal bracket and it comes out with hoses and attacments

the pump is clamped to the bottom of the bracket so you simply clamp it back in the same place once your done

to remove the assembly you need to feel inide and slide the bracket up and to the side and it unlocks

the access panel is in the raised section of the boot on the right hand side and yes the plastic cap is a pain to get off its so tight

i recomend removing the battery from the car during tank opening

less chance of sparks

byt he time you figure out the how the bracket comes out you will be well and truly high even if your tank is almost empty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...