Jump to content
SAU Community

Recommended Posts

G'day, one question and yes i've ran a search.

At the moment i'm a little confused so I apologise if this is a newb question ;)

I have changed the water pump, marked the timing belt, and put it back on correctly. But the thing is, when I turn the engine over manually (tensioning it) the marks are moving and not lining up with the cam gears? I.e One full rev the marks would have moved say 2-3 teeth along the cam gears, and it is like this on both the intake and exhaust. Is this normal? I can't remember if it is but I would think it's not.

Cheers!

Edited by GTAHH
Link to comment
https://www.sau.com.au/forums/topic/117890-rb20-timing-alignment-help/
Share on other sites

G'day, one question and yes i've ran a search.

At the moment i'm a little confused so I apologise if this is a newb question ;)

I have changed the water pump, marked the timing belt, and put it back on correctly. But the thing is, when I turn the engine over manually (tensioning it) the marks are moving and not lining up with the cam gears? I.e One full rev the marks would have moved say 2-3 teeth along the cam gears, and it is like this on both the intake and exhaust. Is this normal? I can't remember if it is but I would think it's not.

Cheers!

yes im guessing this is normal.. i had the same dillema with my rb25, i freaked out when i first saw it, but if you wind in over backwards they re align... so the teeth havnt moved.... i hope :

You will probably find that the number of teeth on the belt is not an even multiple of the teeth on the cam wheels.

All that is important is that the marks on the cam wheels and the mark on the crank pulley line up at TDC #1.

The marks on the belt are there to help you set it up easy, once you turn the donk they wont mate again. As long as the cam gear marks mate with the marks on the backing plate when the crank pulley is on TDC you got it right .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...