Jump to content
SAU Community

Recommended Posts

can i mention that it takes alot longer then 15mins to get to nudgee from springwood crazy clarks.

maybe for you :)

its ok these are approx times. I'll be in contact with the groups and we'll wait till everyone's there

  • Replies 248
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I'm in as always:) Can we have a city area meet up in Milton maybe? coz I have no idea where nudgee is, besides, it will be more fun cuising there with other skylines.

Mud....

I can lead the milton group if you like as milton is closer for me then meeting those at springwood.

consider it a deal. call must be placed within a 5 minute window of 6:20am to qualify for 1kg of M&Ms.

Doneded....so based on your criteria I can call between 6:15am and 6:25am? Thats within the 5 min window of 6:20am, unless you say it must be after 6:20am...

We should sync our watches

Do M&Ms look the same on the way out?

Eeeeeewwwwwwwwww :D

h guys

i'm new out to make new friend so me and my 34 should be there....

Hi There,

Would be good to meet you. Cya there.

--------------

And Karen,

You are correct, between 6:15 and 6:25am and we should sync our watches.

At the beep it will be 4:11pm

.

..

...

....

.....

BEEP.

Mark,

Marc and I will lead the Springwood group if you haven't got anyone else yet.

BTW is there anyone from down Springwood way who is actually coming on this event, coz if there isn't I'm not going all the way down to Springwood from Toowong and I will lead the Milton group instead :)

Milton group can meet at the BP on Milton Road :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...