Jump to content
SAU Community

Recommended Posts

Hi guys

Ever since I bought my r32 rb20det I get this weird problem when driving and only recently I found the symptoms of it

Sometimes when I start it (cold start) I have to tap the throttle to get the revs up then it idles perfectly with no problems and warming up is fine

When im driving at like 60kmh in fifth gear I put the clutch in and the revs go all the way to 0rpm and battery light comes on etc, but if I tap the throttle it the revs would go up accordingly and then get back off the clutch it will come back to life as in the revs would be back to normal

Is this something to worry about?

Sometimes also at low speeds, if I'm on the clutch and I apply the brake really hard to stop at intersections it does the same thing and the revs die to 0rpm and all lights come on, but then tap the throttle or clutch out and it kicks back itself again...

Could it be some sort of leak somewhere?

Any advice would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/120014-weird-rpm-problem-at-certain-speeds/
Share on other sites

then it could be an inlet leak from a split vacuum hose or injector seals, you can test for this with a can of degreaser/rp7/WD40/carbi cleaner - if there is a leak, then the spray gets sucked in and the engine revs will rise as it burns that fuel..

give it a try on vacuum hoses, injectors, between the upper and lower sections of the plenum etc etc

thanks guys will give it a go

yeah i sprayed before just near my plenum i had a leak there on inlet manifold

i have changed my inlet manifold gasket because inside cylinder 5 and 6 air was choking a bit there and its all fixed now so no more severe idle problems, like the car is driveable now but just if you jump hard on brake or clutch in the revs will go down severely but then kick up again

yeah start up issues on cold

when i start it on cold without tapping the throttle it is hard to start

i have had my alternater reconditioned so it's like brand new

on my apexi pen timer it shows 12.2 - 12.5 volts on the battery but the reading also flashes indicating it is also at low voltage

i'm planning to buy a new battery soon but there is no problem with it being charged

i have this same problem its really pissin me off gota get to the bottom of it now

stalls coming up to lights on clutch in/brake and have to heel toe blip accel to keep it alive, starts 1 in 5 cranks too :laugh:

ive sorted the battery, coil packs, plugs and wired fuel pump to 100% duty (040 just making sure lower setting wasnt causing stall) and no love

next i guess ill check afm, aac, injectors :

yeah my problem seems identical to yours inissane although my car is driveable only when i get on the brake hard with clutch in it stalls but then comes back

also hard to start aswell like you said

i might try battery

ive changed afm aswell

and ive cleaned aac valve ;p

i wired my fuel pump aswell to the boot so it bypasses the ecu (could be the problem?) i might change that back this weekend

will post results

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...