Jump to content
SAU Community

Recommended Posts

As, topic says.....I have a custom made ( YES!!!! CUSTOM MADE) HKS N1 REPLICA muffler for N/A car

It's has 3" inlet and 4" tip

lookin at $350ono

Have pics......sorry about da quality as they were from my gay webcam hahahaha :D

http://www.pbase.com/lancer_boy/gay_webcam

Link to comment
https://www.sau.com.au/forums/topic/12079-replica-hks-n1/
Share on other sites

sn00p..........I am sorry to say but I actually dun know...... When I bought it....it was for my lancer...which is N/A...

can somebody tell me whats da difference so I can clear this up...

Thnx

Link to comment
https://www.sau.com.au/forums/topic/12079-replica-hks-n1/#findComment-217875
Share on other sites

omg..

u f00li0

NA cars need backpressure..

turbo cars need greater flow..

if u stick that N1 muffler on a turbo car.. it will reduce performance..

if u put it on a NA car.. it will increase performance..

Link to comment
https://www.sau.com.au/forums/topic/12079-replica-hks-n1/#findComment-217904
Share on other sites

sif..........it's not that easy...and especially for a lancer 1.8 3" inlet is way to big and it's N1 (canon style) then it's straight through....gonna loose so much in da low end

Maybe better for 2.0 L N/A cars...........so all N/A skyline's.........Supra's......Celica's......etc

buy buy buy

Link to comment
https://www.sau.com.au/forums/topic/12079-replica-hks-n1/#findComment-217920
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...