Jump to content
SAU Community

Recommended Posts

Bolt on type, need repair on one bend just before it attaches to the cat, eveything else is perfect working order, 3" piping and a 4" tip, full stainless system, i assume it will only cost $80 or so for a local shop to cut out the bend and make another mandrel bent corner (cheaper if pressure bent)

photos of system and a close up of the bend are here

i'd like to sell this asap as i have no use for it as i wanted a 3 1/2"system not a 3" and i bought the wrong system hehe, so im out of pocket about $680 (what i paid for it form hikari performance (was listed for $780 on their website)

PAID $700

SELL $600 (BARGAIN!)

call 0411 50 54 58 or email [email protected] or just reply to this thread or PM me :D thanks guys

  • 3 weeks later...

Offer - $325 pick-up in Melb. Can send a friend. Let me know if interested as friend is driving up to Bris to visit us on Thursday. PM me and we'll talk acc't details if interested.

iijj

Originally posted by iijj

Offer - $325 pick-up in Melb.  Can send a friend.  Let me know if interested as friend is driving up to Bris to visit us on Thursday.  PM me and we'll talk acc't details if interested.

iijj

dude that offer isnt even worth considering

Originally posted by Raza

will it fit on a r33 4 door

not as it is now but when u get the dent repaired u can tell them to do it so it will fit, may cost an extra $10 but really shouldnt cost anymore as its the benmd they charge for doing, they will be able to make it fit

  • 2 weeks later...

cmon $600 is a bargain for this exhaust, full stainless steel, ya'd pay $1200+ easily for something of this quality brand new, but i must stress its $600 FIRM im losing enough money on this as it is :D

  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...