Jump to content
SAU Community

Recommended Posts

hey everyonee...

Just got a slight issue with the air con demister...

the aircon blows air through every vent. Wen i try to turn on the demister nothing comes out to clear the fog of the front windscreen (rear works fine) the rest of the vents are ok work normal.

also in summer the air con blows warm air and not cold.

Have run the air con diagnostic and it came up with no problems at all.....

anyone have any ideas ????

or have had the same issue ???

Please advise

thanks fellas.................

Link to comment
https://www.sau.com.au/forums/topic/120995-aircon-demister/
Share on other sites

You've got the right button, correct?

Which button are you hitting to turn on the front demister?

Do the other airvents stop when you push the button? Or do they keep blowing air. If that's the case, then it sounds like the flap that directs the air into different vents may have stopped working. Or the bar could have fallen out of place.

Link to comment
https://www.sau.com.au/forums/topic/120995-aircon-demister/#findComment-2230874
Share on other sites

yehh im positive its the right one

it has the funny symbol on it

heres the pic of which button im pressing

The other vents work fine and do not stop or decrease in air flow at all

i think ur right, it culd be the flap because it also makes like a loud clicking noise wen i press the button, and the clicking only stops wen i turn off the aircon.......

post-26606-1149559290.jpg

Link to comment
https://www.sau.com.au/forums/topic/120995-aircon-demister/#findComment-2231119
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...