Jump to content
SAU Community

Recommended Posts

Extreme 9 puck cushioned button with antiburst cover. $850 supplied , fitted with machined flywheel and includes new thrust bearing.

Have them in everything from SR's to GTR's and will hold up to 350-400rwhp.

Extra $30 if your gearstick boot seal is leaking which 90% of them do.

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/121880-new-clutch/#findComment-2248158
Share on other sites

Extreme 9 puck cushioned button with antiburst cover. $850 supplied , fitted with machined flywheel and includes new thrust bearing.

Have them in everything from SR's to GTR's and will hold up to 350-400rwhp.

Extra $30 if your gearstick boot seal is leaking which 90% of them do.

Cheers

Ken

awsome clutchs :D ken and the boys put one in my r33 over 2years ago.. still going strong with my new power level and the abuse i give it at the drift prastices

Link to comment
https://www.sau.com.au/forums/topic/121880-new-clutch/#findComment-2256719
Share on other sites

I've got a brand new genuine Nissan R33 clutch sent over from Japan sitting at home, willing to part with it for the same price I paid for it.

I bought it thinking my extreme clutch one was dodgy but it turned out to be fine just not adjusted properly. Pm me if your interested.

My 33 has got a Extreme ceramic clutch as well, good clutch when adjusted properly, pretty jumpy though.

-michael

Link to comment
https://www.sau.com.au/forums/topic/121880-new-clutch/#findComment-2257216
Share on other sites

Extreme 9 puck cushioned button with antiburst cover. $850 supplied , fitted with machined flywheel and includes new thrust bearing.

Have them in everything from SR's to GTR's and will hold up to 350-400rwhp.

Extra $30 if your gearstick boot seal is leaking which 90% of them do.

Cheers

Ken

How are these to drive on every day?

Link to comment
https://www.sau.com.au/forums/topic/121880-new-clutch/#findComment-2275249
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...