Jump to content
SAU Community

Recommended Posts

Hey people,

looking at a few r34 gt-t's. there are alot of hight km (100 000+) on the market at very reasonable prices. what are the life expectancy, risks, turbo life etc on say a mild mod, regular seviced vehical? how many km's have you done? and what problems if any have you incured?? and info would be appreciated. regards Damian :devil:

Link to comment
https://www.sau.com.au/forums/topic/122395-expected-engine-life/
Share on other sites

Hey people,

looking at a few r34 gt-t's. there are alot of hight km (100 000+) on the market at very reasonable prices. what are the life expectancy, risks, turbo life etc on say a mild mod, regular seviced vehical? how many km's have you done? and what problems if any have you incured?? and info would be appreciated. regards Damian :devil:

hey mate, i just recently bought a gtt, only done 34ks when i picked it up, and got it for $29.5k, insured with justcar, reasonable cost.. around 2900

3 year warrenty on all parts, is running great atm, high boosted it couple time, otherwise runs on 6psi..

watelse, got catback and couple aftermarket gauges and controller, pretty stock otherwise

hope this helped..

Mines done 86K and is still smooth as, even though i thrash it a bit. Feels similar to when i got it which was 60K. I change the oil rougly every 5K klms - note it isn't the smoothest 6 around so you may think it sounds rough when you first drive it. btw mine's fairly stock.

I would be quite surprised if the k's in the previous post are genuine (tho not sure of medel yr)- i wouldn't trust a pre 2000 model that's done less than 40K. Make sure you change filters and belts espicially if 100,000 service hasn't been done.

The expected engine life of all these RB engines are rated at at least 250,000kms. Read that somewhere, i'll try to put the article up.

The NEO RB25s are improved versions from the older RB25. The 34 shouldn't have a problem up to 300,000kms i reckon. Just look at those RB20s and RB26s in the R32 GTRs, most of them are still running really well even after 160ks.

My 2 Cs

I wouldn't place a huge focus on kilometers, for one thing most skylines odometers have been tampered with. When you test a car you can gauge by the condition of interior (wear on g/stick s/wheel, drivers seat, etc) and how it drives as to the condition of the car and engine, plus get a mechanical inspection. If the engine is in good running order, and u change oil every 5,000km and service every 10,000km you should have a very long running engine.

My family still has a nissan '82 bluebird with over 400,000km that still runs, despite not being looked after nearly as well as it could have been. Nissan engines are generally quite reliable and built to last and if well looked after will go for ages.

Just my 2 cents

Edited by r32line

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...